Quantum SNC 4000 Скачать руководство пользователя страница 114

Страница: 114 / 164

108

Service Port Command Reference

setNettime [value]

The

setNettime

command enables or disables timeserver functionality.

SNC4000 > setNettime 1

Nettime 1 value = 0 = 0x0

setScsiAssign [devID], [channel], [id], [lun]

The

setScsiAssign

command assigns a target device to a SCSI channel [channel] with SCSI Target ID

[id] and Logical Unit Number of [lun].

The indicated channel must be configured to be running in target mode. The [id] and [lun] must be available
on that channel.

The example below shows the device with devID of 64 assigned to ID 0, LUN 0 on SCSI Channel 2.

SNC4000 > setScsiAssign 64,2,0,0

Parameter

Value

Port

Changes will apply to all FC
Connections

Changes will apply to the FC
Connection (Connection 1)

“

”

“

aix

”

“

solaris

”

“

hp-ux

”

“

linux

”

“

netware

”

“

gateway

”

“

generic

”

“

unisys

”

“

adic snc

”

“

pv-132t-fc

”

“

autosense/nt

”

CAUTION

You must reboot the SNC 4000 after executing this command for the
new setting to take effect.

Value Meaning

Disables timeserver functionality

Enables timeserver functionality

Note

When you are using Firmware 4.40 on a Fibre Channel blade, this command is
unavailable.

Note

The

targets

command displays the devID as the Idx.

Содержание SNC 4000





































































































































































Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды

Quantum SNC 4000, Руководство пользователя

Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды