Quantum SNC 4000 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 164

background image

SNC 4000 User’s Guide

105

scsiHostIdSet [channel],[id]

The

scsiHostIdSet

command sets the Host ID for a specified SCSI Channel.

SNC4000 > scsiHostIdSet 2,7

Host Id set to 7 for SCSI 2

will take effect upon reboot

value = 0 = 0x0

scsiRescan [channel]

The command

scsiRescan

requests a SCSI rescan for new devices. If channel is specified (1 or 2), then

only that channel is scanned. Otherwise, if channel is not specified or if channel is 0, then all channels are
scanned.

SNC4000 > scsiRescan 2

Done

value = 0 = 0x0

Rescanning a SCSI bus may delay I/O commands pending on that bus for several seconds. Do not rescan
SCSI buses when this delay may not be tolerated. When possible, only scan the bus where a new device
has been added.

When a device is discovered, there may be further device specific initialization that continues after the scan
has completed in which case the device may not show up immediately when you issue the

fcShowDevs

command. An example of this is a disk that requires a SCSI Start Unit command to become ready. (Tape
and Changer devices and Disks that indicate Ready status are available on scan completion).

If a SCSI target device should require replacement, remove the old device, set the new device to the same
SCSI bus ID as the old device and attach it to the same channel. Rescan the channel to update the
configuration data. The new device should be available to host systems with the same LUN as the old
device.

scsiResetDisableGet [channel]

The

scsiResetDisableGet

command displays the SCSI Bus Reset On Power Up is enabled. False

means that SCSI Bus Reset On Power Up is disabled.

SNC4000 > scsiResetDisableGet

SCSIbus Reset Disable ------- ---------------

SCSI 1 TRUE

SCSI 2 FALSE | default

value = -1 = 0xffffffff

scsiResetDisableSet [channel],[mode]

The

scsiResetDisableSet

command sets the SCSI Bus Reset On Power Up for the specified SCSI

channel. False is default and enables reset of SCSI bus on power-up. True disables SCSI bus reset on
power-up.

Parameter

Value

SCSI Channel Number

1 - 2

ID

0 -15

CAUTION

You must reboot the SNC 4000 after executing this command for the
new settings to take effect.

«
...
109
110
111
112
113
...
»

Содержание SNC 4000





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SNC 4000

Бренд: R/Evolution Страницы: 58

InTANK iR2775-S3

Бренд: Raidon Страницы: 21

Бренд: Raidon Страницы: 2

Бренд: Euromate Страницы: 23

Бренд: US Robotics Страницы: 156

Бренд: Galvo Shed Страницы: 2

Бренд: Ferm Страницы: 4

Бренд: SmartDisk Страницы: 2

PowerBay 4-Bay RAID Multi-Interface Drive

Бренд: Verbatim Страницы: 11

Бренд: GARDEN MASTER Страницы: 8

Бренд: Rowlinson Garden Products Страницы: 5

Бренд: Corvus systems Страницы: 21

RUGGED BOSS SSD

Бренд: LaCie Страницы: 68

Бренд: Lifeline Страницы: 13

TANDEMBOX intivo

Бренд: BLUM Страницы: 2

Бренд: ABSCO SHEDS Страницы: 16

Hexawood 10035764

Бренд: Blumfeldt Страницы: 16

PROFILE XP PFR 500

Бренд: GRASS VALLEY Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды