Pro-face GP3000 Series Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 164

background image

When an error message is displayed (Error code list)

Maintenance/Troubleshooting

1-92

WinGP SDK startup failure

WinGP installation

Error Message

Cause and Solution

Reference

Could not launch the installer
of WinGP SDK

Configuration of the installer is incor-
rect.
Install the program from the GP-Pro
EX CD.

)

GP-Pro EX

Installation Guide

Error Message

Cause and Solution

Reference

You cannot install WinGP
when Pro-Server with Pro-Stu-
dio is installed.
First uninstall Pro-Server with
Pro-Studio, then continue
installing WinGP. WinGP can
co-exist with Pro-Server EX
V1.10 or higher, which has the
same functionality as Pro-
Server with Pro-Studio.

After uninstalling Pro-Server with Pro-
Studio, install WinGP.
If you need functions of Pro-Server
with Pro-Studio, use Pro-Server EX
V1.10 or later version.

)

GP-Pro EX Refer-
ence Manual
“37.3.2 Setup
Procedure u
Installation Proce-
dures” (page 37-
12)

You cannot install WinGP
when any version before
V1.10 of Pro-Server EX is
installed. You can continue
installing after you either unin-
stall Pro-Server EX, or
upgrade to Pro-Server EX
V1.10 or higher.

Install WinGP after uninstalling a ver-
sion of Pro-Server EX older than
V1.10, or after upgrading Pro-Server
EX to V1.10 or later.

A different version of Pro-
Server EX is already installed.
Please uninstall, and then con-
tinue installing Pro-Server EX.

If you try to install Pro-Server EX of a
version older than V1.10 into IPC
where WinGP has already been
installed, this error message is dis-
played. In this case, use Pro-Server EX
V1.10 or later version.

You cannot install Pro-Server
EX when the WinGP SDK is
installed. Uninstall WinGP and
continue installing Pro-Server
EX?
Note: WinGP SDK applica-
tions are compatible with Pro-
Server EX. All you need to do
is set up the network node in
Pro-Server.

If you select [Yes], Pro-Server Ver1.10
will be installed after WinGP SDK is
uninstalled.
To use an application that has been cre-
ated with WinGP SDK, register the
WinGP node name [#WinGP] in NPX.
If you select [No], installation is inter-
rupted.

«
...
90
91
92
93
94
...
»

Содержание GP3000 Series





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GP3000 Series

Бренд: Easson Страницы: 33

Бренд: Taylor-Wharton Страницы: 25

Бренд: Quark-Elec Страницы: 2

Бренд: V.ORLANDI Страницы: 144

Бренд: Branick Страницы: 7

Бренд: Holland Green Science Страницы: 54

Бренд: Terrier Страницы: 36

UMEN-260314-V1.0

Бренд: NewHawk Страницы: 14

Бренд: Hanns.G Страницы: 2

Бренд: Cooler Master Страницы: 18

Бренд: Dynamic Displays Страницы: 29

Бренд: ALANTIK Страницы: 10

ROBA-brake-checker plus DC 028.600.2

Бренд: Mayr Страницы: 10

Бренд: Speco Страницы: 1

Бренд: Hanns.G Страницы: 24

Бренд: MSI Страницы: 31

Бренд: Dynascan Страницы: 28

Бренд: switel Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды