Pro-face GP3000 Series Скачать руководство пользователя страница 65

Страница: 65 / 164

Problems with communication with connected devices

Maintenance/Troubleshooting

1-65

1.4.2 Communication fails on specific screens

Is an error code displayed on the GP?

If communication fails on specific screens, first check the error code displayed on the screen.

Cause

If an communication error occurs only when a specific screen is opened, a part or a script may
be using the unsupported device addresses used on the base screen where the error occurred.

Continued

Typical error No.

Main cause

RHAA006 to RHAA007

Check if any noises are generated. Check the cable connection
and connector engagement.

RHAA010 to RHAA012

This error is displayed during Ethernet communication.
Check the port No. and network environment.

RHAA033 to RHAA035

This error is caused by the connected device. For details, see
the GP-Pro EX Device/PLC Connection Manual.

RHAA036 to RHAA037

This chapter describes these errors only. For other errors, see the fol-
lowing section.

)

“1.6.2 Display-related errors u Errors displayed when communication fails”

(page 1-130)

Address outside of the device range is used.

RHAA038

An attempt was made to read data which is write-only.

RHAA039

An attempt was made to write to data which is read-only.

RHAA040 to RHAA045

This error is caused by the connected device. For details, see
the GP-Pro EX Device/PLC Connection Manual.

RHAA065 to RHAA066

This is a typical error displayed when communication using
Ethernet fails. Check the communication settings and IP
address.

RHAA067 to RHAA070

This is a typical error displayed when communication using
RS-232C/422/485 fails. Check the communication settings
and cable connection.

RHAA070:PLC1:The cable has been disconnected or the target has been
powered off

Error
code

RHAA070:PLC1:The cable has been disconnected or the target has been
powered off

Beep

100

200

300

111

222

Error
code

Содержание GP3000 Series





































































































































































Результаты поиска

Содержание GP3000 Series

Отзывы:

Похожие инструкции для GP3000 Series

Бренды по названию

Популярные бренды

Pro-face GP3000 Series, Техническое обслуживание и устранение неисправностей

Результаты поиска

Содержание GP3000 Series

Отзывы:

Похожие инструкции для GP3000 Series

Бренды по названию

Популярные бренды