background image

When an error message is displayed (Error code list)

Maintenance/Troubleshooting

1-107

1503 Font 

 

Settings

The specified font 
has not been regis-
tered in “Fonts for 
Projects”.Add it, in 
“Font Settings”, or 
change the font. 

Add the font using “Font Set-
tings” in the system settings or 
change the font.

)

GP-Pro EX Refer-
ence Manual “6.4 
[Font] Settings 
Guide” (page 6-
19) 

1504 Project 

Information

Backup SRAM use 
exceeds the maxi-
mum capacity. 
Operations that 
cannot be backed 
up in SRAM will not 
run. Check the set-
tings in the Project 
Information.

Make sure the total capacity 
of SRAM to use does not 
exceeds approximately 
320KB (approximately 
120KB only for GP-3202B).

)

GP-Pro EX Refer-
ence Manual “5.7 
Viewing Project 
Information” 
(page 5-41) 

1505 Sampling 

Settings

Sampling settings 
backed up to SRAM 
exceeds the avail-
able retentive data 
area.  Excess data 
cannot be pre-
served.

The setting of the group for 
which “Backup to SRAM” is 
set to OFF exceeds the range 
of the data storage area.
Reduce the sampling words or 
the number of sampling times 
so that the setting remains 
within the range of the data 
storage area.

)

GP-Pro EX Refer-
ence Manual 
“24.9.1 Sum-
mary  u DRAM” 
(page 24-101) 

1506

The project con-
tains features that 
require a CF Card. 
However, the 
selected display 
does not support 
CF cards so these 
features will not 
run.

The GP3202B model supports 
the CF-card export folder. 
Change the model or do not 
set the CF-card output folder.

)

GP-Pro EX Refer-
ence Manual 
“5.14.6 [System 
Settings] Setting 
Guide  n [Device/
PLC] Setting 
Guide” (page 5-
142) 

)

GP-Pro EX Refer-
ence Manual “5.7 
Viewing Project 
Information” 
(page 5-41) 

1507 Global D-

Script

The number of 
devices limit has 
been exceeded. 
The total number of 
allowable devices in 
the all Global 
Scripts is 255.

Make sure the total number of 
addresses to use in Global D-
Scripts (including calling 
functions) does not exceed 
256 by creating multiple 
scripts with the same trigger 
conditions and separating 
instructions.

)

GP-Pro EX Refer-
ence Manual 
“20.9.1 D-Script/
Global D-Script 
Restrictions” 
(page 20-59) 

1508 Global D-

Script

The total number of 
Global D-Scripts 
and functions 
exceeds the maxi-
mum limit of 32. 
The excess code 
will not run.

Make sure the total number of 
Global D-Script and func-
tions does not exceed 32 by 
uniting multiple scripts with 
the same trigger conditions.

Continued

Error 

No.

Screen

ID/No./Line

Error Message

Handling method

Reference

Содержание GP3000 Series





































































































































































Отзывы: