Pro-face GP3000 Series Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 164

background image

When an error message is displayed (Error code list)

Maintenance/Troubleshooting

1-148

Errors starting with REAA

RAAE006 Recent history data

is too big. Restoring
previous history
data.

If the volume of the stored history
data file is larger than the size speci-
fied in GP-Pro EX, and the previous
history data is normal, this error mes-
sage appears. Normally, this error
does not occur but may occur when a
history data file is exchanged. In this
case, restore the previously saved his-
tory data, and then restart the GP.

—

RAAE007 Recent history data

is corrupted.

If the history data file is damaged, the
checksum of the history data file does
not match, and the previous history
data is normal, this error message
appears. In this case, restore the pre-
viously saved history data and then
restart the GP.

—

RAAE008 [LanSys.cfg] File is

missing. Using initial
value.

If no Lansys.cfg file exists, this error
message appears. In this case, the
local node name and port settings will
be reset to the initial settings. Re-
enter the local node name and port
while in offline mode.

—

RAAE009 [system.cfg] File is

missing. Using initial
value.

If no system.cfg file exists, this error
message appears. In this case, all set-
tings in [Main Unit Settings] will be
reset to the initial settings. Transfer
the project file again.

—

Error No.

Error Message

Cause and Solution

Reference

REAA016 Could not use the

XXX port (No: XXX).

Opening the XXX (UDP or TCP) port
No. (XXX) failed. The system port
number may have been used already.
Please check the system port number
and use available one.

—

REAA017 Attempted to access

a write-protect area
(XXX)

You cannot write to the write-pro-
tected area (LS0000 to LS0019,
LS2032 to LS2095, LS9000 to
LS9999) using a D-script or across
the network. Please do not write data
to the write-protected area using a D-
script or across the network.

—

Continued

Error No.

Error Message

Cause and Solution

Reference

«
...
146
147
148
149
150
...
»

Содержание GP3000 Series





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GP3000 Series

Бренд: I-Tech Страницы: 16

13.3 inch HDMI LCD (H)

Бренд: Waveshare Страницы: 12

Бренд: Acer Страницы: 15

Бренд: Vivid Страницы: 75

Бренд: M-system Страницы: 2

Бренд: Dantel Страницы: 46

Бренд: CueScript Страницы: 5

Бренд: Eaton Страницы: 2

Бренд: Tronair Страницы: 11

VG910B - 19" LCD Monitor

Бренд: ViewSonic Страницы: 21

Бренд: ViewSonic Страницы: 25

Бренд: Unipart Dorman Страницы: 39

HANNS-G HL247HGB

Бренд: HANNspree Страницы: 23

Бренд: YAKUMO Страницы: 23

Бренд: Plura Страницы: 46

Бренд: Schmalz Страницы: 36

Бренд: zitrek Страницы: 37

SN 5620-15000 Series

Бренд: Strack Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды