Pro-face GP3000 Series Скачать руководство пользователя страница 102

Страница: 102 / 164

When an error message is displayed (Error code list)

Maintenance/Troubleshooting

1-102

Template

Duplicate

Part List

Parts Selection Toolband

Error Message

Cause and Solution

Reference

Failed to read the target tem-
plate.

Select a different template.

—

Error Message

Cause and Solution

Reference

Failed to create the specified
number of duplicates
because the set address
range was exceeded. The
limit is up to

∗∗∗

Delete unnecessary parts, if any, and
duplicate the parts again.

)

GP-Pro EX Refer-
ence Manual “5.15.1
Restrictions for Cre-
ating Screens n
Number of Features
that can be Placed
on a Screen” (page
5-165)

Failed to make the specified
number of duplicates
because of exceeding the set
address range.

For parts that have multiple addresses,
this message displays even if only one
address exceeds the range.
Specify the address range and dupli-
cate the parts again.

—

Error Message

Cause and Solution

Reference

Failed to export to the target
file.

Check the export destination file or
disk and export to it again.

—

Error Message

Cause and Solution

Reference

Failed to read the target file.

The specified image file is damaged, or
is not in BMP or JPEG format. Check
the file to read and the drive.

—

Failed to write to the target
file.

The file failed to write. Check the file
to write and the drive.

Содержание GP3000 Series





































































































































































Результаты поиска

Содержание GP3000 Series

Отзывы:

Похожие инструкции для GP3000 Series

Бренды по названию

Популярные бренды

Pro-face GP3000 Series, Техническое обслуживание и устранение неисправностей

Результаты поиска

Содержание GP3000 Series

Отзывы:

Похожие инструкции для GP3000 Series

Бренды по названию

Популярные бренды