Omron Q2V Series, Техническое руководство

Страница: 323 / 734

Parameter
List
11
11.4 b: APPLICATION
SIEPCYEUOQ2V01A Q2V Technical Manual 323
No.
(Hex.)
Name Description
Default
(Range)
Ref.
b5-12
(01B0)
Fdback Loss Select
Mode
Sets the drive response to PID feedback loss/excess. Sets drive operation after the drive
detects PID feedback loss/excess.
0 : DO Only Always
1 : AL+DO Always
2 : FLT+DO Always
3 : DO Only@PID Enable
4 : AL+DO@PID Enable
5 : FLT+DO@PID Enable
0
(0 - 5)
474
b5-13
(01B1)
Fdback Loss Lvl
Sets the level that triggers PID Feedback Loss [FbL] detection as a percentage of the
Maximum Output Frequency.
Note:
Parameter A1-02 [Control Method] selects which parameter is the maximum output
frequency.
•
A1-02 ≠ 8 [EZ Vector] : E1-04 [Max Output Frequency]
• A1-02 = 8 : E9-02 [Maximum Speed]
0%
(0 - 100%)
475
b5-14
(01B2)
Fdback Loss Time
Sets the length of time that PID Feedback must be less than b5-13 [Fdback Loss Lvl] to
detect PID Feedback Loss [FbL] .
1.0 s
(0.0 - 25.5 s)
475
b5-15
(01B3)
Sleep Start Level
Sets the output level that triggers the PID Sleep function.
Determined by A1-02
(0.0 - 590.0)
475
b5-16
(01B4)
Sleep Delay Time
Sets a delay time to start or stop the PID Sleep function.
0.0 s
(0.0 - 25.5 s)
475
b5-17
(01B5)
RUN
PID Accel/Decel Time
Raises or lowers the PID setpoint using the acceleration and deceleration times set to
the drive. This is a soft-starter for the PID setpoint.
0.0 s
(0.0 - 6000.0 s)
475
b5-18
(01DC)
b5-19 PID SP Selection
Sets the function that enables and disables b5-19 [PID Setpoint Value] .
0 : Disabled
1 : Enabled
0
(0, 1)
476
b5-19
(01DD)
RUN
PID Setpoint Value
Sets the PID setpoint when b5-18 = 1 [b5-19 PID SP Selection = Enabled] .
0.00%
(0.00 - 100.00%)
476
b5-20
(01E2)
PID Unit Selection
Sets the number of digits to set and show the PID setpoint.
0 : 0.01Hz units
1 : 0.01% units
2 : rpm
3 : User Units
1
(0 - 3)
476
b5-34
(019F)
RUN
PID Out Low Limit
Level
Sets the output lower limit for the PID control as a percentage of the Maximum Output
Frequency.
Note:
Parameter A1-02 [Control Method] selects which parameter is the maximum output
frequency.
• A1-02 ≠ 8 [EZ Vector] : E1-04 [Max Output Frequency]
• A1-02 = 8 : E9-02 [Maximum Speed]
0.0%
(-100.0 - +100.0%)
476
b5-35
(01A0)
RUN
PID In Hi Limit Level
Sets the output upper limit for the PID control as a percentage of the Maximum Output
Frequency.
Note:
Parameter A1-02 [Control Method] selects which parameter is the maximum output
frequency.
• A1-02 ≠ 8 [EZ Vector] : E1-04 [Max Output Frequency]
• A1-02 = 8 : E9-02 [Maximum Speed]
1000.0%
(0.0 - 1000.0%)
477
b5-36
(01A1)
PID HiHi Limit Level
Sets the level that triggers Excessive PID Feedback [FbH] as a percentage of the
Maximum Output Frequency.
Note:
Parameter A1-02 [Control Method] selects which parameter is the maximum output
frequency.
•
A1-02 ≠ 8 [EZ Vector] : E1-04 [Max Output Frequency]
•
A1-02 = 8 : E9-02 [Maximum Speed]
100%
(0 - 100%)
477
b5-37
(01A2)
PID HiHi Time
Sets the length of time that the PID feedback signal must be more than the level set in
b5-36 [PID HiHi Limit Level] to cause Excessive PID Feedback [FbH] .
1.0 s
(0.0 - 25.5 s)
477
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV