SIEPCYEUOQ2V01A Q2V Technical Manual
211
Minor Fault/Alarm
Code (Hex.)
Name
0020
SE [Modbus Test Mode Error]
0021
L24v [Loss of External Power 24 Supply]
0022
oH3 [Motor Overheat (PTC Input)]
0027
FbL [PID Feedback Loss]
0028
FbH [Excessive PID Feedback]
002A
dnE [Drive Disabled]
0032
AEr [Station Address Setting Error]
0033
CyC [MECHATROLINK CommCycleSettingErr]
0034
HCA [High Current Alarm]
0035
LT-1 [Cooling Fan Maintenance Time]
0036
LT-2 [Capacitor Maintenance Time]
0039
EF1 [External Fault (Terminal DI1)]
003A
EF2 [External Fault (Terminal DI2)]
003B
SToF [Safe Torque OFF Hardware]
003D
oL5 [Mechanical Weakening Detection 1]
Minor Fault/Alarm
Code (Hex.)
Name
003E
UL5 [Mechanical Weakening Detection 2]
0042
TrPC [IGBT Maintenance Time (90%)]
0043
LT-3 [SoftChargeBypassRelay MainteTime]
0044
LT-4 [IGBT Maintenance Time (50%)]
0045
boL [Braking Transistor Overload]
0049
qAL1 [Q2pack Alarm]
004A
qAL2 [Q2pack Alarm 2]
004B
qAL3 [Q2pack Alarm 3]
0081
EP24v [External Power 24V Supply]
0085
bAT [Keypad Battery Low Voltage]
0087
CP1 [Comparator 1 Limit Error]
0088
CP2 [Comparator 2 Limit Error]
0089
TiM [Keypad Time Not Set]
008A
bCE [Bluetooth Communication Error]
◆
Error Codes
■
Modbus Communications Error Code List
This table lists the Modbus communications error codes.
When an error occurs, remove the cause of the error and restart communications.
Table 6.15 Modbus Communications Error Codes
Error Code
(Hex.)
Name
Cause
01
Function Code Error
The PLC set a function code that was not 03, 08, or 10 (Hex.)
02
Register Number Error
•
The register number that is trying to access is not registered.
•
A starting number that was not 0001 or 0002 (Hex.) was set when broadcasting.
03
Bit Count Error
•
Read and write data quantities are more than the 1 to 16 range. (Command message data quantity is disabled.)
•
The data that was read from non-consecutive holding registers contained more than 120 bytes.
•
The data to be written to non-consecutive holding registers contained more than 60 bytes.
•
In the write mode, the number of bytes in the message is not the number of data × 2.
21
Data Setting Error
•
Writing control data or parameters made the settings go out of the permitted setting range.
•
A parameter setting error occurred when writing a parameter.
22
Write Mode Error
•
Tried to write a disabled parameter during run.
•
When there was a
CPF06 [Control Circuit Error]
, the master tried to write a parameter other than one of these:
–
A1-00 [Language Selection]
–
A1-01 [Access Level]
–
A1-02 [Control Method]
–
A1-03 [Init Parameters]
–
A1-04 [Password Input]
–
A1-05 [Password Setting]
–
E1-03 [V/f Pattern Selection]
–
o2-04 [Drive KVA Selection]
•
Writes the read-only data.
23
DC Bus Undervoltage
Write Error
During
Uv [DC Bus Undervoltage]
, a
Uv
write disabled parameter was written.
24
Error Writing Data During
Parameter Processing
Tried to write a parameter from the master during parameter processing on the drive side.
25
Writing into EEPROM
Disabled
Writing into EEPROM write is disabled, but EEPROM write was executed from Modbus communications. When this error
occurs, the keypad shows a message and the drive continues operation.
Содержание Q2V Series
