OMRON
PART 1: CX-Programmer
CX-Programmer_Page (xxiv)
Improvements to Program Editing Efficiency
•
Read Only Mode
Previous version (Ver. 3.3)
New version (Ver. 4.0)
When editing a program offline,
editing could not be prohibited.
Allowing ladder screen display only, and prohibiting
program editing by mistake while offline is possible.
Set the
Offline Edit Mode
to
Read Only Mode
in the
Option
Dialog Box to enable this function.
When editing a program, an
operation could be reversed
(Undo), but all the edited parts
could not be selected to be
either applied (store) or
cancelled.
After temporary editing of a specific rung, the user
can select to utilize (store) or delete (cancel) the
editing results.
Select
Read Only Mode Edit – Start Edit
from the
Edit
Menu, and then perform either of the following
steps after editing.
a) To apply the editing results, select
Read Only
Mode Edit – Store
from the
Edit
Menu. The edited
contents will be reflected in the program.
b) To not apply the editing results, select
Read Only
Mode Edit – Cancel
from the
Edit
Menu. The edited
contents will be deleted.
Therefore, after editing rungs and writing and
recording temporary changes, the changes can be
selected to be either applied or deleted, enhancing
program editing efficiency
Improvements to Program Development in Task Units
•
Downloading by Task (Program) (CS/CJ-series CPU Unit Ver. 2.0 or Later)
Previous version (Ver. 3.3)
New version (Ver. 4.0)
When downloading a program
to the PLC, only the whole
user program could be
downloaded.
Note: Uploading in sections or
tasks (program) was possible
when using CS/CJ-, or
CVM1/CV-series PLCs.
Programs can be downloaded to CS/CJ-series PLCs
Ver. 2.0 or later, and downloading by task (program)
instead of the whole user program is possible.
Select
Partial Transfer – Task Transfer to PLC
from the
PLC
Menu, and download a specified single task or
multiple tasks.
This function enhances the efficiency of program
development by multiple personnel.
Particularly, by downloading to the PLC by task
(program, only the parts to be changed are reflected in
the PLC, resulting in fewer working errors.
Содержание CX-Programmer 9
