manualshive.com logo in svg

Omnia 7AM, Руководство пользователя

Поделиться
Скачать
Omnia 7AM Скачать руководство пользователя страница 46

CHAPTER 10 | 

37

AM MENU

 

♦

Switching to 

Intermediate 

mode makes a significantly larger number of controls available and is much 

more akin to Expert mode than Basic. For instance, the three simple controls for multiband adjustments 
in Basic mode are replaced by three entire menus that allow complete control over parameters like attack 
rate, release rate, targets, and thresholds for each band of the multiband AGC’s and multiband limiters. 

 

♦

Intermediate mode is best suited for anyone who knows the art of processing well, understands how these 
controls work and interact with one another, and wants to fine tune their sound with tools that are not 
available in Basic mode.

 

♦

Expert 

mode makes visible every available control in Omnia.7, including some that are admittedly rarely 

used by anyone except factory preset authors. While there are some very powerful controls available in 
this mode, our experience with Omnia.9 over the past several years (the product upon which Omnia.7 
is based) is that they are best left alone unless you are intimately familiar with the intricacies of these 
products and have a very specific need to make changes to these settings. 

 

♦

But as we sometimes say, “We just build the Ferrari - we don’t issue driver’s licenses”, so all of the tools 
are here regardless of whether they get used to set a record lap time or crash before the green flag finishes 
dropping!

Switching Between Modes

The current mode is part of the 

About Preset

 menu (more about that control later). The important thing to 

remember is that you can freely switch back and forth between Basic, Intermediate, and Expert modes without 
losing any settings. 

This is an important ability and not one widely offered in other processors that feature multiple levels of user 
adjustment, and it affords you the flexibility to do something like this to hone your sound:  Pick a preset that’s close 
to the sound you are after, do some fundamental adjustments to the bass in Basic mode, switch to Intermediate for 
some bass fine tuning, go back to Basic mode to open up the dynamics a bit, go back into Intermediate to adjust the 
attack time of a single band, then go back to Basic to set the final clipper to achieve the desired loudness. In other 
words, you are never locked into the Intermediate or Advanced modes once you’ve left the Basic mode.

Processing in Basic Mode

Switching to and from Basic mode is done in the 

AM > Processing > About Preset

 menu.

The 

Processing

 menu in Basic mode contains eleven sub-menus, including 

Load Preset, Save Preset, Preset 

Protection, About Preset, Input Conditioning, Enhance, Gain Riding, Multiband, Final, Bypass

 and 

Clipper.

 The 

front panel only has room to display the first nine so be sure to move “down” to see the last two. (Yet another great 
reason to use the NfRemote app instead of the front panel interfaceJ).

Содержание 7AM












































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды