Omnia 7AM страница 109 Скачать руководство пользователя

Страница: 109 / 139

CHAPTER 16 |

100

SYSTEM MENU

Source Adjustment Menu

The

Source Adjustment

menu contains the controls to set the input gain and L/R channel balance, invert polarity,

and swap the left and right channels of the input audio. Independent silence thresholds are also provided for each
input.

♦

The

Input Gain

control allows you to adjust a variable gain stage after the clip detector and can be used to

boost levels to meet Omnia.7’s reference input level as indicated by a green color on the input meters over
a range of 18dB.

♦

The

Balance

slider provides a means by which to dial in a fixed left-to-right channel gain offset. This

can be useful if something ahead of Omnia.7 (board, DA, STL) introduces a L/R gain shift that cannot
otherwise be corrected. Positive values indicate increased gain in the right channel. Negative numbers
indicate more gain in the left channel.

♦

The

Invert

control allows you to swap the polarity of only the left channel input, only the right channel

input, or both the left and right channels simultaneously.

♦

The

Mode

control offers five combinations to determine how the input audio is fed into Omnia.7 in terms

of left and right channels.

L/R

sends left channel input audio to the left channel and right channel input audio to the right

channel (default setting).

R/L

sends left channel input audio to the right channel and right channel input audio to the left

channel.

L+R

sends both right- and left-channel input audio to both the left and right channels.

sends only left-channel input audio to both the left and right channels.

sends only right-channel input audio to both the left and right channels.

Содержание 7AM











































































































































Результаты поиска

Содержание 7AM

Отзывы:

Похожие инструкции для 7AM

Бренды по названию

Популярные бренды

Omnia 7AM, Руководство пользователя

Результаты поиска

Содержание 7AM

Отзывы:

Похожие инструкции для 7AM

Бренды по названию

Популярные бренды