DMTA-10040-01EN, Rev. E, February 2018
List of Figures
351
Adjusting the lift-off angle to horizontal ..................................................... 188
Materials—dual frequency for corrosion ..................................................... 190
The Dual Frequency Sub-Surface application ............................................. 191
The list of dual frequency parameters .......................................................... 192
Figure 5-100 Position 1 of the standard ............................................................................... 193
Figure 5-101 Adjusting the angle of the frequency 1 lift-off signal ................................. 193
Figure 5-102 Adjusting the angle of the frequency 2 lift-off signal ................................. 194
Figure 5-103 Position 2 on the standard .............................................................................. 194
Figure 5-104 The frozen signals ............................................................................................ 195
Figure 5-105 Adjusting the gain for frequency 1 ............................................................... 195
Figure 5-106 Adjusting the gain for frequency 2 ............................................................... 196
Figure 5-107 Adjusting the H GAIN for frequency 1 ........................................................ 197
Figure 5-108 Adjusting the H GAIN 2 value ...................................................................... 197
Figure 5-109 Adjusting the H GAIN value ......................................................................... 198
Figure 5-110 Adjusting the H MIX GN value ..................................................................... 199
Figure 5-111 Adjusting the V MIX GN value ..................................................................... 199
Figure 5-112 The corrosion-defect scan result .................................................................... 200
Figure 5-113 The list of all parameters ................................................................................ 201
Figure 5-114 Materials—dual frequency for sub-surface cracks ..................................... 202
Figure 5-115 The Dual Frequency Sub-Surface application ............................................. 203
Figure 5-116 The list of dual frequency parameters .......................................................... 204
Figure 5-117 Position 1 on the standard .............................................................................. 205
Figure 5-118 Adjusting the ANGLE value .......................................................................... 205
Figure 5-119 Adjusting the ANGLE 2 value ....................................................................... 206
Figure 5-120 Adjusting the amplitude of the frequency 1 signal .................................... 206
Figure 5-121 Adjusting the amplitude of the frequency 2 signal .................................... 207
Figure 5-122 The fastener scan result .................................................................................. 208
Figure 5-123 Adjusting the horizontal amplitude of the frequency 1 signal ................. 208
Figure 5-124 Adjusting the vertical amplitude of the frequency 1 signal ...................... 209
Figure 5-125 Adjusting the horizontal amplitude of the frequency 2 signal ................. 209
Figure 5-126 Adjusting the vertical amplitude of the frequency 2 signal ...................... 210
Figure 5-127 Position 3 on the standard .............................................................................. 211
Figure 5-128 Adjusting the V GAIN 2 value ....................................................................... 211
Figure 5-129 Adjusting the V GAIN value .......................................................................... 212
Figure 5-130 Checking the Mix signal ................................................................................. 212
Figure 5-131 Adjusting the ANGLE value .......................................................................... 213
Figure 5-132 Adjusting the H GAIN 2 value ...................................................................... 213
Figure 5-133 The scan results for both fastener rows ........................................................ 214
Figure 5-134 The list of all parameters ................................................................................ 215
Содержание nortec 600
