Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 25 / 185

background image

Total Station DTM-322 Instruction Manual

11

Preparation

2

•

After charging the battery, do not recharge it until it has been fully discharged.
Recharging a fully charged battery lowers its performance.

•

If the battery is used in low temperature (below 0 °C or 32 °F), the capacity is
reduced and provides shorter operation time than when used at room
temperature.

•

If a battery is not used for a long period, it can never be charged to its full
capacity again.

•

Battery pack BC-65 is not compatible with this instrument.

Detaching and Re-Attaching the Battery Case

Detaching the battery case

C

CAUTION – Avoid touching the contacts on the battery case.

1.

If the instrument is turned on, press

[PWR]

to turn it off.

2.

Depress the battery mounting button while holding the battery case.

Attaching the battery case

Before you attach the battery case, clear any dust or other foreign particles from the
battery contacts.

1.

Hold the instrument steady with one hand.

2.

Fit the two projections at the bottom of the
battery case into the concave sections at the
bottom of the instrument.

3.

Press the battery mounting button.

4.

Push the battery case against the instrument
and release the battery mounting button.
Make sure that the battery mounting button
is fully released and the battery is securely
attached to the instrument.

C

CAUTION – If the battery case is not attached securely, this could adversely affect the
watertightness of the instrument.

3

4

2

1

«
...
23
24
25
26
27
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: Keithley Страницы: 49

Бренд: Kane Страницы: 16

Бренд: Bacharach Страницы: 48

Бренд: Bacharach Страницы: 24

Бренд: Macnaught Страницы: 14

Бренд: DAE Страницы: 28

Бренд: Tactical Controls Страницы: 11

Бренд: FarmChem Страницы: 8

CP-4900 Micro-GC

Бренд: Varian Страницы: 7

Бренд: Vapotherm Страницы: 2

Бренд: Midcontinent Страницы: 6

Бренд: RHS Страницы: 8

Duomat Evolution DeLuxe

Бренд: Dennerle Страницы: 27

Бренд: Seaward Страницы: 2

Бренд: OmegaWatt Страницы: 9

Engine Analyzer Series

Бренд: ACCEL DFI Страницы: 39

Бренд: Xylem Страницы: 39

Fusion-L 6 digit

Бренд: London Electronics Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды