Nikon HQA46480 Скачать руководство пользователя

Страница: 139 / 185

Total Station DTM-322 Instruction Manual

125

Menu Key

As each record in the current job is output from the
instrument (downloaded), the current line number is
updated.

After downloading is completed, you can choose to
delete the current job.

To delete the current job, press

[4]

. To return to the

Basic Measurement Screen (BMS), press

[ESC]

or the

Abrt

softkey.

Uploading coordinate data

To upload coordinate data from a computer, press

[2]

select

Upload XYZ

in the Communication menu.

The default data format appears. To change the order
of data fields, press the

Edit

softkey. For more

information, see

Advanced feature: Editing the data

order for upload, page 126

Otherwise, just press

[ENT]

To change the communication settings, press the

Comm

softkey. The serial port settings must match the settings
used by the terminal software on the computer.

Use an RS-232C cable to connect the instrument to the
computer.

The Free space field shows the number of points that
can be stored.

Press

[ENT]

to put the instrument in receive mode. Then

use the Send Text File command in the terminal program on the computer to start
sending data.

Press the

Job

softkey to go to the Job Manager screen. For more information, see

Job Manager, page 88

In the terminal program, set flow control to Xon/Xoff.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды