Nikon HQA46480 Скачать руководство пользователя

Страница: 86 / 185

Applications

Total Station DTM-322 Instruction Manual

Sight the second point and press

[MSR1]

[MSR2]

The distances between the first and second point
are displayed.

To change display screens, press

[DSP]

To record the distance and angle information as
a comment record, press

[ENT]

in the 1/2 or 2/2

observation screen.

Default point numbers are displayed. You can
change these point numbers. To record a note,
press

[ENT]

in the To field.

Measuring between the current point and the immediately preceding point

To enter the RDM (Continuous) function, press

[4]

or select

RDM(Cont.)

in the Programs menu.

Follow the procedure as for a radial RDM
measurement. For more information, see

Measuring between the current and the first
point measured, page 71

rSD

Slope distance between two points

rVD

Vertical distance between two points

rHD

Horizontal distance between two points

rAZ

Azimuth from first point to second point

rV%

Percentage of grade (rVD/rHD) × 100%

rGD

Vertical grade (rHD/rVD) :1

Data that you save in RDM functions is stored in RM records. For more information, see

RM records, page 112

When you download data in Nikon RAW format, they are output as comment (CO) records.

Difference between “1:Cont.” and “2:Radial”

1:Cont.

(The preceding two points are

subject to calculation.)

2:Radial.

(Calculations are made with

reference to the first point.)

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды