Nikon HQA46480 Скачать руководство пользователя

Страница: 71 / 185

Total Station DTM-322 Instruction Manual

Applications

Sight the BM point and press

[MSR1]

[MSR2]

Press [ENT].

.

The updated station coordinates are displayed.
You can change the HI in this screen.

To record the updated STN, press

[ENT]

Checking and resetting the backsight direction

To enter the backsight (BS) check function,
press

[5]

or select

BS Check

in the Stn Setup

menu.

Do one of the following:

–

To reset the horizontal angle to the HA set in the last station setup sight the
BS and press the

Reset

softkey or press

[ENT]

–

To cancel the process and return to the BMS, press the

Abrt

softkey or

press

[ESC]

When the HI is changed, the Z coordinate is updated before the station is recorded. You must complete a station
setup before you use the Remote Benchmark function.

You must complete a station setup before you use the BS check function.

This function always refers to the backsight point from the last ST record stored in the current open job.

Current HA reading

The HA to the BS in the last station setup. Enter
station coordinates for observations without recording
data.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды