Nikon HQA46480 Скачать руководство пользователя

Страница: 99 / 185

Total Station DTM-322 Instruction Manual

Applications

Sample records

SS, 58, 0.0000, 48.3304, 169.19165, 82.02470, 10:52:37, FLOOR2

CO, PT1, 1.0080, 48.3020,169.19165, 83.58565

CO, PT2, 1.0080, 48.3155,128.54250, 85.42440

CO, O/S MSR:40 0.0000 0.0000 169.20370 87.02340

Measuring circle offsets

To enter the circle center calculation function,
press

[7]

or select

Circle

in the Offset menu.

If you have not taken a measurement to the
circle before entering this function, a temporary
measurement screen appears.

Sight any point on the surface of the circle and
press

[MSR1]

[MSR2]

Sight one edge of the circle and press

[ENT]

Sight the other edge of the circle and press

[ENT]

The calculated corner point is stored as an SS record. The next three or four comment records are measured
points.

For example: CO, Point name (fixed to PT1, PT2 etc.), HT, SD, HA, VA.

If you use a prism attached to the surface of the circle for the distance measurement, press the

+SD

softkey to

eliminate the offset error (from the attached point to the measured surface of the prism) before you press

[ENT]

If you have taken a distance measurement to the center of the circle, press the

Calc

softkey to calculate the

offset using one edge angle observation.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды