Nikon HQA46480 Скачать руководство пользователя

Страница: 68 / 185

Applications

Total Station DTM-322 Instruction Manual

Sight PT1 and press

[MSR1]

[MSR2]

To proceed to the next point, press

[ENT]

Enter the second point (PT2) and its height of
target.

Measure to PT2 and press

[ENT]

When the instrument has enough data, it
calculates the station (STN) coordinates.

–

If more than the minimum required data is
available, a standard deviation screen
appears.

–

To take measurements to strengthen
geometry of the resection, press the

Add

softkey. For information about the

View

softkey, see

Advanced feature: Viewing and

deleting a measurement in resection,
page 55

When the results are satisfactory, record the
station. To do this, press

[ENT]

or the

REC

softkey.

Enter the height of instrument, if required. Press

[ENT]

. The ST field defaults to the last recorded

PT + 1.

10. To change the station name, move to the ST field

and edit or replace the text.

If you have set Split ST to Yes, the ST field defaults to the last recorded ST value + 1. For more information, see

Others settings, page 109

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды