Nikon HQA46480 Скачать руководство пользователя

Страница: 41 / 185

Total Station DTM-322 Instruction Manual

Getting Started

If the battery level is critically low, the following
message appears:

Adjusting lighting and sound levels

LCD backlight

To turn the LCD backlight on or off, press the illumination key

. To adjust the

backlight level, use the 2-switch window described below.

2-switch window

Use the 2-switch window to adjust lighting and sound
settings for the instrument.

To open the 2-switch window from any screen, hold
down the Illumination key for one second.

To cycle through the settings for a switch, press the
number beside that switch. For example, to turn the backlight on or off, press

[1]

Alternatively, to highlight the switch that you want to set, press

[^]

[v]

. Then press

[ENT]

to cycle through the settings for that switch.

Switch 1 (backlight)

Switch 2 (Sound)

Contrast adjustment window

When the 2-switch window is open, press

[<]

[>]

display the contrast adjustment window. Then press

[^]

[v]

to change the contrast level. The arrow indicates

the current contrast level. To return to the 2-switch
window, press

[<]

[>]

When you have finished changing display light and
sound settings, press

[ESC]

to close the 2-switch or contrast adjustment window.

LCD backlight is on.

LCD backlight is off.

Sound is on.

Sound is off.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды