Nikon HQA46480 Скачать руководство пользователя

Страница: 59 / 185

Total Station DTM-322 Instruction Manual

Getting Started

Measurement settings

To view the measurement settings, hold down

[MSR1]

[MSR2]

for one second.

Use

[^]

[v]

to move the cursor between the fields. Use

[<]

[>]

to change the value in the selected field.

Target field

If the measurement is started with the Target field set
to Prism, there is a dash “–” in front of the prism
constant.

If the measurement is started with the Target field set
to Sheet, there is a right parenthesis “)” in front of the
prism constant.

The symbol then constantly runs from left to right over the prism constant in the
display.

Rec mode field

Field

Values

Target

•

Prism

•

Sheet

Const (prism constant)

–999 mm through 999 mm

Mode

•

Precise

•

Normal

AVE (Average count)

0 (continuous) through 99

Rec mode

One of the following:

•

MSR only

•

Confirm

•

ALL

The Target setting is used to apply better cyclic-error adjustment in distance measurement. It efficiently
eliminates multipath reflection.

The Rec mode setting controls how the

[MSR1]

and

[MSR2]

keys operate in the BMS.

The MSR only setting is the default measurement mode. After a measurement, the instrument stops in the BMS
and waits for you to press

[ENT]

before recording the point.

The Confirm setting displays the Record PT screen before data is recorded.

The ALL setting is a quick shooting and recording mode. The instrument automatically records the point using
the default PT/CD. The instrument then returns to the BMS for the next measurement.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды