Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 24 / 185

background image

2

Preparation

10

Total Station DTM-322 Instruction Manual

C

WARNING –

Children should be supervised while handling the batteries.

C

WARNING –

Do not use different types of batteries together.

C

WARNING –

Do not peel off or damage the outer surface of the battery cell.

C

WARNING –

If leaked liquid gets on the skin or clothing, wash off with clean water immediately.

C

WARNING –

Do not connect 10 or more batteries in series.

C

WARNING –

If something appears wrong with the charger and/or batteries, disconnect the

charger from the AC outlet immediately and contact your dealer.

C

WARNING –

Disconnect the charger from the AC outlet promptly once charging is complete.

C

WARNING –

Be sure to charge the batteries where the ambient temperature is between 0 °C

and 35 °C (32 °F and 95 °F).

C

WARNING –

Be sure to use the charger with correct power source of 100-240 V AC.

Specified battery

SANYO Electric Co, Ltd. Nickel-Metal Hydride Battery HR-3UTG

Notes

•

Charge the battery indoors where the ambient temperature is between 0 °C and
35 °C (between 32 °F and 95 °F). Outside of the indicated range, the battery’s
performance may deteriorate and the battery’s life may become short. If you try
to charge the battery when the ambient temperature is outside this range, the
protective circuit will activate and prevent it from being charged normally.

•

To prevent malfunction, keep the charging plug clean.

•

The battery may discharge while it is stored in the instrument or charger. Don’t
store the battery in the instrument or charger for a long time (more than 1
month). When the instrument is not used for a long time, the battery should be
taken out of the battery case to prevent leakage or rusting. If leaked liquid gets
on the skin or clothing, wash off with clean water immediately.

•

During the charge, the battery and charger will become warm. This is normal.

«
...
22
23
24
25
26
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: WAGER Страницы: 22

Acuvim-L Series

Бренд: AccuEnergy Страницы: 83

Бренд: Callaway Страницы: 11

Бренд: D-tect Systems Страницы: 19

HYDROMETTE BL Compact TF-IR 2

Бренд: GANN Страницы: 40

Бренд: Gamry Страницы: 16

Бренд: Oceanic Страницы: 68

Бренд: Oceanic Страницы: 24

Бренд: Pangea Страницы: 2

Бренд: DGH Страницы: 87

Бренд: Magnescale Страницы: 64

SourceMeter 2430

Бренд: Keithley Страницы: 141

HYDROMETTE HB 30

Бренд: GANN Страницы: 65

Бренд: Fly Henry Страницы: 5

Бренд: Toro Страницы: 60

Бренд: Hanna Instruments Страницы: 2

American AL-1000

Бренд: Badger Meter Страницы: 16

C100L-L-DD-LE-5-OV1-SV1-PV1C-V1-S1

Бренд: Sierra Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды