Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 35 / 185

background image

Total Station DTM-322 Instruction Manual

21

Getting Started

3

Sleep mode

If you press the

Sleep

softkey in the Press

[ENT]

→

OFF screen, or enable the Power Save setting (see

Power saving, page 107

), the instrument goes into

sleep mode.

When the instrument is in sleep mode, it wakes up if
any of the following occurs:

•

You press a key

•

The instrument receives a remote control command

•

You rotate the alidade

•

You tilt the telescope

Selecting a Language

The Nikon total station supports one Language Pack at a time. The Language Pack is
a set of up to three different languages installed on the instrument from which the user
can select. Several Language Packs are available for the Nikon total stations.

•

Language Pack #1: English, French, Spanish

•

Language Pack #2: English, German, Italian

•

Language Pack #3: English, Chinese, Russian

1.

To select a different language, power on the
instrument and press

[ESC]

and

[3]

at the Tilt

Telescope screen.

The Select Language screen appears. Up to
three languages are available in the installed
Language Pack. The screen shows which
languages are currently available on the instrument.

The current language selection is highlighted.

the

Sleep

softkey

put the instrument into power-saving mode

[ESC]

cancel the power-off process and return to the previous screen

If you press the

Reset

softkey, the software is rebooted and the Basic Measurement Screen (BMS) appears

without an open job.

Press ...

To ...

«
...
33
34
35
36
37
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: WattNode Страницы: 57

Бренд: Kanomax Страницы: 31

Бренд: Hach Страницы: 196

Бренд: QLA Страницы: 18

LM-OG-P2 Advanced

Бренд: Badger Meter Страницы: 48

Бренд: Badger Meter Страницы: 24

Бренд: Bahco Страницы: 92

Бренд: Cablescan Страницы: 58

Бренд: MadMan Страницы: 37

Бренд: MADDALENA Страницы: 5

Бренд: OHAUS Страницы: 32

Бренд: Vaisala Страницы: 2

STORA-ABG RKS-01

Бренд: ECOTEST Страницы: 146

Бренд: Hanna Instruments Страницы: 2

American AL-1000

Бренд: Badger Meter Страницы: 16

Photo Research PR-810

Бренд: Jadak Страницы: 120

Бренд: Hanna Instruments Страницы: 2

Smart Photometer System iDip 570

Бренд: eXact Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды