Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 32 / 185

background image

2

Preparation

18

Total Station DTM-322 Instruction Manual

Face-1/Face-2 Measurements

You can take a measurement from either face of the instrument. To change the face,
rotate the instrument 180° on its base, and rotate the telescope 180° within the
standard.

By averaging the Face-1 and Face-2 measurement values, you can cancel out most
constant mechanical errors. Some errors, such as vertical axis error, cannot be
cancelled out by averaging Face-1 and Face-2 measurements.

C

CAUTION – When rotating the telescope, take care not to catch your finger in the gap between
the instrument’s standard and the telescope.

A Face-1 measurement is made with the vertical circle positioned to the left of the
telescope eyepiece. A Face-2 measurement is made with the vertical circle positioned
to the right of the telescope eyepiece.

Face-1

Face-2

«
...
30
31
32
33
34
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: ECC X-RAY Страницы: 14

Бренд: IET Labs Страницы: 114

Бренд: Valcom Страницы: 1

Бренд: J&D Electronics Страницы: 2

Бренд: Dakota Digital Страницы: 34

Бренд: Value Страницы: 20

Бренд: Z-TRAUQ Страницы: 10

Бренд: wtw Страницы: 72

Бренд: Benetech Страницы: 16

Бренд: GE Страницы: 16

Celviano AP-650M

Бренд: Casio Страницы: 84

Бренд: FLIR Страницы: 21

Бренд: Danfoss Страницы: 2

Бренд: ScienTECH Страницы: 18

Бренд: Radiation Alert Страницы: 22

Бренд: YOKOGAWA Страницы: 2

Бренд: Behringer Страницы: 2

Бренд: Autometers Systems Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды