Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 131 / 185

background image

Total Station DTM-322 Instruction Manual

117

Menu Key

5

–

In the detailed data screen, press the

Edit

softkey.

2.

Use

[^]

or

[v]

to highlight a field. Then modify the

value in the selected field.

3.

To finish editing, press

[ENT]

in the CD field.

A confirmation screen appears.

4.

Do one of the following:

–

To accept the changes and return to the data
view screen, press

[ENT]

or the

Yes

softkey.

–

To go back to the edit screen, press

[ESC]

or

the

No

softkey.

Editing station records

Note – The system will not recalculate measurements if you change the station record.
All coordinate and raw data observed from an edited station record must be
recalculated in your postprocessing software.

In the RAW screen, use

[^]

or

[v]

to highlight the station

record that you want to edit. Then press the

Edit

softkey.

You can edit any field in the ST record, but the
instrument does not recalculate any measurements
from this station.

Press

[ENT]

in the AZ field to confirm the change.

If you change the ST or HI values, the coordinates of observation points are not recalculated. A comment record
is stored to record the change. The following example shows a comment record for a changed HI value:

CO,HI changed at ST:9012 Old HI= 1.3456m

If you change the BS or AZ values, raw records are not recalculated. A comment record is stored to record the
change.

«
...
129
130
131
132
133
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: Vcheck Страницы: 31

Бренд: Eagletone Страницы: 2

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 101

Charge Analyzer 711

Бренд: 3M Страницы: 24

Бренд: National Instruments Страницы: 18

Бренд: JUMO Страницы: 24

Бренд: LEM Страницы: 33

Бренд: Lutron Electronics Страницы: 43

Бренд: PANCONTROL Страницы: 157

Бренд: 365SMART Страницы: 20

Бренд: E+E Elektronik Страницы: 48

Бренд: Eddy Wireless Страницы: 18

Expert PDU energy 8001

Бренд: Gude Страницы: 22

Бренд: ILITCH ELECTRONICS Страницы: 2

Бренд: Benetech Страницы: 16

PowerMaster MTA15Z

Бренд: PowerMetrix Страницы: 13

Бренд: Fluke Страницы: 2

Бренд: Badger Meter Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды