Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 23 / 185

background image

Total Station DTM-322 Instruction Manual

9

Preparation

2

C

WARNING –

Never burn or heat the battery. Doing so may cause the battery to leak or rupture.

A leaking or ruptured battery can cause serious injury.

C

WARNING –

Before storing the battery or battery charger, cover the contact points with

insulation tape. If you do not cover the contact points, the battery or charger may short circuit,
causing fire, burns, or damage to the instrument.

C

WARNING –

The battery is not itself waterproof. Do not get the battery wet when it is removed

from the instrument. If water seeps into the battery, it may cause a fire or burns.

C

WARNING –

Use the battery specified in this manual. Using the other battery may lead to be

lower performance, it may cause a fire or burns.

C

CAUTION – Before charging the battery, read the instruction manual for the charger and the
battery.

To Charge the battery

This charger is designed to charge 1 to 4 cells of AA Ni-MH rechargeable battery.

Before charging the battery, please read the attached instruction.

1.

Place the battery cells into the compartments of the charger,
where the polarity (+/-) of the battery cell should be
connected with the same polarity indicated in the charger.
Do not plug the cell in reverse polarity.
When charging 1 to 2 AA cells at a time, insert them into
the end positions.

2.

Plug the charger into an electrical outlet of 100-240 V AC
after placing the battery cells into the charger. The charger
indicator light is illuminated and battery charging begins.

Note – Do not insert or remove the battery cells during this charging process.

3.

When charging is completed, the indicator light turns off. Remove the battery
cells from the charger.
If charging is still incomplete after 6 hours of charging, stop charging.

4.

Disconnect the charger from the AC outlet.

C

WARNING –

Do not insert the battery with the (+) and (-) ends reversed.

C

WARNING –

Do not bring the (+) and (-) terminals into contact with metal objects. When

carrying or storing the batteries, avoid direct contact with metal objects.

«
...
21
22
23
24
25
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: Parkside Страницы: 94

Wind Monitor Series

Бренд: Campbell Страницы: 38

Бренд: Favero Electronics Страницы: 12

ProcessMaster FEP630 series

Бренд: ABB Страницы: 92

Бренд: National Instruments Страницы: 15

Бренд: DGH Страницы: 87

Бренд: X-Rite Страницы: 130

Бренд: Vega Страницы: 52

Бренд: Kane Страницы: 52

Бренд: ABQ Industrial Страницы: 32

Concert Monochord

Бренд: FEELTONE Страницы: 8

Бренд: Duratool Страницы: 4

Бренд: Ditel Страницы: 2

Бренд: R&S Страницы: 1611

Бренд: PCB Piezotronics Страницы: 17

Бренд: Hanna Instruments Страницы: 2

Бренд: Hameg Страницы: 6

Бренд: TA ENGINEERING Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды