Nikon HQA46480 Скачать руководство пользователя

Страница: 105 / 185

Total Station DTM-322 Instruction Manual

Menu Key

A confirmation screen appears.

Do one of the following:

–

To set the selected job as the control job,
press

[ENT]

or the

Yes

softkey.

–

To cancel the process, press

[ESC]

or the

softkey.

Displaying job Information

To display job information, highlight the job name and
then press the

Info

softkey.

The Information screen shows the number of records in
the job, the free space, and the date when the job was
created. Free space indicates how many points can be
stored in the job.

To return to the job list, press any key.

If a control job is already assigned, the newly assigned control job replaces it
as the control job.

To clear the control job selected, highlight the current control job in the job list
and press the

Ctrl

softkey. Then press

[ENT]

or the

Yes

softkey to confirm.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды