Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 156 / 185

background image

7

Specifications

142

Total Station DTM-322 Instruction Manual

External Device Connector

This connector can be used to communicate with an external device.

Before using the external device connector, make sure that the external device meets
the specifications below.

C

CAUTION – Except for the connection shown in

, use of this connector

is at your own risk.

C

CAUTION – Use only the male connectors specified above. Using other connectors will
damage the instrument.

The external device connector is a Hirose HR 10A-7R-6S female connector. The
pinouts for connecting it to an external device connector are shown below:

C

CAUTION – Use only the pin connections shown above. Using other connections will damage
the instrument.

To communicate with an external device, connect the RS-232C signal from the
external device to Pin 1 (input terminal) and to Pin 2 (output terminal) on the
instrument.

Cap the data output/input connector securely while not in use. The instrument is not
watertight if the cap is not attached or not attached securely, and when the data
output/input connector is in use.

The instrument can be damaged by static electricity from the human body discharged
through the data output/input connector. Before handling the instrument, touch any
other conductive material once to remove static electricity.

System

RS-232C

Signal level

±9 V standard

Maximum baud rate

38400 bps asynchronous

Compatible male connector

Hirose HR10A-7P-6P or HR10-7P-6P

Pin

Signal

Description

1

RxD

Receive data (Input)

2

TxD

Send data (Output)

3

No connection

5

–

Ground

4, 6

No connection

HRS

1

6

2

5

3

4

«
...
154
155
156
157
158
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: KBR Страницы: 12

Бренд: Kawai Страницы: 72

DGX Gears XTRA Regulator

Бренд: Dive Gear Express Страницы: 26

Бренд: X-Rite Страницы: 130

WJ-NX310K Series

Бренд: i-PRO Страницы: 18

Бренд: CWT Страницы: 41

Бренд: International Light Technologies Страницы: 19

Бренд: STM Страницы: 31

Бренд: BAPI Страницы: 3

SXP30 - ELECTRONIC PIANO

Бренд: Technics Страницы: 12

Бренд: MFJ Страницы: 5

Dynasonics IS-4000

Бренд: Badger Meter Страницы: 36

Бренд: MTE Страницы: 113

Бренд: Liquivision Страницы: 84

Бренд: M-system Страницы: 8

Бренд: GREISINGER Страницы: 16

Бренд: INTERSPIRO Страницы: 32

Eutech Expert pH

Бренд: Thermo Scientific Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды