Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 123 / 185

background image

Total Station DTM-322 Instruction Manual

109

Menu Key

5

Others settings

To open the Others menu, press

[9]

or select

Other

in

the Settings menu.

B

Tip – To provide easier configuration for common regional settings, you can quickly configure
the Nikon total station to a pre-set combination of default regional settings. For more
information, see

Changing Regional Configuration Pre-sets, page 22

.

B

Tip – The Nikon total station supports up to 3 languages on the instrument. For more
information on changing the language settings, see

XYZ disp

Fast/Norm/Slow/+ENT

Defines speed to move to the next screen after
showing XYZ of the input PT

2nd Unit

None/Meter/US-Ft/I-Ft

When the Secondary unit is set to a unit, an
extra display screen is available in the BMS,
stakeout observation screens, and 2-pt
reference line screens. The extra screen shows
the HD, VD, and SD in the secondary unit.

If you select US-Ft or I-Ft, an additional settings screen appears. Use this
screen to specify whether to display values in Decimal-Ft or Ft-Inch.

Sig Beep

ON/OFF

Split ST

No/Yes

Select Yes to separate the point numbers of
station points from other record type point
numbers

If you set the Split ST field to Yes, an additional setting screen appears. Use
this screen to specify the starting ST number.

CD Input

ABC/123

Sets the default input mode when a CD field
appears.

Owner’s Detail Up to 20 characters.

Enter your name or the name of your
company. If you enter a value in this field, it
appears at start-up.

«
...
121
122
123
124
125
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: Kane Страницы: 12

Бренд: Eaton Страницы: 53

Бренд: Oceanic Страницы: 75

SMatrix DMX2400

Бренд: dallmeier Страницы: 12

Бренд: Garmin Страницы: 22

Бренд: Vaisala Страницы: 40

Бренд: ProsKit Страницы: 10

Бренд: TQC Sheen Страницы: 16

Бренд: Hammond Страницы: 36

Бренд: SIMET Страницы: 2

Бренд: NARDA Страницы: 60

Privia PX-860BK

Бренд: Casio Страницы: 67

Бренд: HOKUYO AUTOMATIC Страницы: 17

Бренд: paratronic Страницы: 4

Бренд: Aquametro Oil & Marine Страницы: 36

Бренд: Tektronix Страницы: 65

Бренд: Ralcam Страницы: 8

Бренд: Cal Test Electronics Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды