Nikon HQA46480 Скачать руководство пользователя

Страница: 126 / 185

Menu Key

112

Total Station DTM-322 Instruction Manual

RM records

When you record measurements in RDM (Cont) or
RDM (Rad), they are labeled as RM records.

Each RM record consists of two screens.

Press

[DSP]

to switch between the first screen (showing

From, To, rHD, and rVD) and the second screen
(showing rAZ, rSD, rV%, and rGD).

When you download data in Nikon RAW format, RM
records are output as comment (CO) records.

AR records

An AR record stores an area and perimeter calculation.

When you download data in Nikon RAW format, AR
records are output as comment (CO) records.

View coordinate data

When you press

[2]

or select

XYZ data

in the Data

menu, coordinate data appears in a list, with the newest
record at the bottom of the screen. Use

[^]

[v]

to scroll

through the records. Use

[<]

[>]

to move up or down

one page.

Press

[ENT]

to see more detailed information about the

selected record.

UP, MP, CC, and RE records

All coordinate records contain PT, CD, X, Y, and Z fields.

UP records are uploaded point coordinates. MP records are manually input point
coordinates. CC records are points calculated in Cogo, and RE records are points
calculated in Resection.

The header (XYZ,YXZ,NEZ, or ENZ) depends on the Coord. Label setting in

MENU > Settings >

Coord.

For more information, see

Coordinate, page 107

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды