Nikon ECLIPSE MA200 Скачать руководство пользователя страница 35

Страница: 35 / 107

Chapter 3 Operation Details

3.4

Eyepiece Tube

3.4.1

Selecting optical path

•

The light distribution for both the binocular and vertical tube parts of the MA2-TI3 trinocular eyepiece tube

can be performed using the optical path changeover lever.

Figure 3.4-1 Selecting optical path

Light distribution

Lever

position

Binocular tube

Vertical tube

IN (Press)

100

OUT (Pull)

100

•

The light distribution for the eyepiece tube part and the back port can be selected with the eyepiece

tube/back port changeover lever.

Figure 3.4-2 Selecting optical path

Light distribution

Lever

position

Eyepiece tube

Back port

IN (Press)

100

OUT (Pull)

Optical path
changeover lever

Eyepiece tube/back port
changeover lever

Содержание ECLIPSE MA200












































































































Результаты поиска

Содержание ECLIPSE MA200

Отзывы:

Похожие инструкции для ECLIPSE MA200

Бренды по названию

Популярные бренды

Nikon ECLIPSE MA200, Инструкция по эксплуатации

Результаты поиска

Содержание ECLIPSE MA200

Отзывы:

Похожие инструкции для ECLIPSE MA200

Бренды по названию

Популярные бренды