Nikon ECLIPSE MA200 Скачать руководство пользователя страница 51

Страница: 51 / 107

Chapter 3 Operation Details

3.18

Using the

Plate (D-LP)

Figure 3.18-1

plate slider

Attach the D-LP

plate to the sextuple revolving

nosepiece (D-ND6) to perform sensitive color
polarization microscopy under the diascopic
illumination.
The D-LP

plate is not required to use the TI-DIC

plate on the supporting pillar for dia-Illuminator 100W.

3.18.1 Inserting/removing

the

plate from the optical path

Figure 3.18-2 Inserting/removing the

plate

from the optical path

Two slots are provided on the front of the revolving
nosepiece. Insert the D-LP analyzer slider with the
nameplate facing down into the slot (with “

”

indicated) near the objective. When it hits the second
click-stop position, the

plate enters the optical path.

Pull out the slider, and when it hits the first click-stop
position the first red compensator is removed from
the optical path. The dummy hole then enters the
optical path.

Second click-stop
position

First click-stop
position

plate

plate slider

Содержание ECLIPSE MA200












































































































Результаты поиска

Содержание ECLIPSE MA200

Отзывы:

Похожие инструкции для ECLIPSE MA200

Бренды по названию

Популярные бренды

Nikon ECLIPSE MA200, Инструкция по эксплуатации

Результаты поиска

Содержание ECLIPSE MA200

Отзывы:

Похожие инструкции для ECLIPSE MA200

Бренды по названию

Популярные бренды