Nikon ECLIPSE MA200 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 107

background image

Chapter 3 Operation Details

56

3.22

Using the HG Precentered Fiber Illuminator (C-HGFI/C-HGFIE)

Figure 3.22-1 HG Precentered Fiber Illuminator

The specified light source LV-LH50PC may not
provide sufficient brightness to perform epi-fl
microscopy. In such case, use an HG precentered
fiber illuminator that uses a high intensity mercury
lamp as a light source.

3.22.1

Procedure for turning on the power switch

Figure 3.22-2 Procedure for turning on

the power switch

1 Be sure that the fiber illuminator is properly

connected to the MA200 main body.

2 Set the POWER switch to the “|” side to turn on

the fiber illuminator and wait until it starts up.

When the POWER indicator on the fiber
illuminator lights up, the LAMP indicator starts
blinking. Once the illuminator starts up, the LAMP
indicator stops blinking and lights up.

If the C-HGFIE motorized fiber illuminator is in
use, the communication function on the illuminator
does not activate until it starts. Be sure to wait until
the illuminator starts up.

3 Set the POWER switch to the “|” side to turn on

the power on the MA200 main body.

The power LED on the front of the MA200 main
body lights up.

4 To turn off the fiber illuminator, set the power

switch to the “

c

” side in the sequence of the fiber

illuminator, the MA200 main body.

* To use the HG precentered fiber illuminator

correctly, carefully read the instruction manual
supplied with the fiber illuminator and make sure
to follow the instruction.

HG Precentered
Fiber Illuminator

LAMP indicator

POWER indicator

2

Power switch ON

1

Power switch ON

«
...
56
57
58
59
60
...
»

Содержание ECLIPSE MA200












































































































Отзывы:

Нет отзывов

Похожие инструкции для ECLIPSE MA200

Бренд: Olympus Страницы: 16

Fluoview FV1000

Бренд: Olympus Страницы: 3

Fluoview FV1000

Бренд: Olympus Страницы: 28

Бренд: Olympus Страницы: 7

Бренд: Olympus Страницы: 16

Бренд: Olympus Страницы: 45

Бренд: Olympus Страницы: 64

Бренд: FEI Страницы: 224

Бренд: Bresser Страницы: 12

Бренд: Bresser Страницы: 20

Бренд: Bresser Страницы: 28

Бренд: Ivation Страницы: 18

Бренд: Levenhuk Страницы: 50

MED PRO 600 Fluo

Бренд: Levenhuk Страницы: 128

Бренд: AmScope Страницы: 19

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 12

Axiovert 5 digital

Бренд: Zeiss Страницы: 56

Бренд: Zeiss Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды