Nikon ECLIPSE MA200 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 107

background image

Chapter 3 Operation Details

34

3.4.2

Adjusting the eyelevel risers

Eyelevel risers can be used to adjust the height of the
eyepiece tube for the user’s eye point. Up to two
eyelevel risers can be attached in piles. When one
eyelevel riser is attached, the eyepiece height rises
25 mm.

If you look through the objective that is 10X or
less than 10X when two eyelevel risers are
attached on the microscope, the rim of the
view-filed may look different from the one without
an eyelevel riser due to reduction of light
intensity.

Figure 3.4-3 Adjusting the eyelevel risers

3.5

Adjusting the Interpupillary Distance

Adjust the interpupillary distance or the distance between the eyepieces according to user’s eye distance.

Figure 3.5-1 Adjusting the interpupillary distance

Before adjusting the interpupillary distance, follow the
procedure described in “2.1 Bright-field Microscopy
under the Episcopic Illumination” or “2.6 Bright-field
Microscopy under the Diascopic Illumination,” and
focus on the sample with the 10X objective.
Look through the eyepieces and adjust the binocular
part until the view fields for the right and left eyes
coincide.
This will facilitate the observation with both eyes.
The binocular part has a scale for interpupillary
distance. It is recommended to memorize or record
your interpupillary distance, so that the distance
between the eyepieces can be readily adjusted next
time.

Eyelevel riser

«
...
34
35
36
37
38
...
»

Содержание ECLIPSE MA200












































































































Отзывы:

Нет отзывов

Похожие инструкции для ECLIPSE MA200

Бренд: Olympus Страницы: 5

Бренд: TME Страницы: 1

Бренд: Accu-Scope Страницы: 4

A23.3645N Series

Бренд: OPTO-EDU Страницы: 17

Бренд: OPTO-EDU Страницы: 16

Бренд: OPTO-EDU Страницы: 36

Бренд: OPTO-EDU Страницы: 59

Бренд: Discovery Kids Страницы: 4

Бренд: Viavi Страницы: 56

Бренд: TOOLCRAFT Страницы: 4

Бренд: Nikon Страницы: 21

Бренд: Jeulin Страницы: 32

Бренд: Nikon Страницы: 42

Бренд: Siemens Страницы: 24

opmi lumera 700

Бренд: Zeiss Страницы: 236

Бренд: Olympus Страницы: 21

Бренд: Olympus Страницы: 22

Бренд: LW Scientific Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды