Nikon ECLIPSE MA200 Скачать руководство пользователя страница 14

Страница: 14 / 107

Chapter 1 Part Name and Function

Figure 1.1-3 Left view, Rear view

Binocular
tube

Vertical
tube

Back port

Supporting Pillar for Dia-Illuminator
100W/Supporting Arm for DS-L2
attaching part

(Refer to 3.23 and 3.24.)
Attach the supporting pillar for
dia-Illuminator 100W or the supporting
arm for DS-L2.

Tool storage

Stores the supplied hexagonal
wrench and two hexagonal
screwdrivers.

Rear-panel clamp screw

Rear-panel

Remove the rear-panel
cover for cable connection
of the revolving nosepiece.

Air vents

Cable keeper

Keeps cables inside.

“CAUTION for heat”
symbol

Epi illumination
lamphouse

(LV-LH50PC Lamphouse)
Attach an HG precentered
fiber illuminator instead of
LV-LH 50PC Lamphouse,
if necessary.

Signal cable hole for the
nosepiece controller 2

Optical path changeover lever
(vertical tube/binocular tube)

(Refer to 3.4.)
Press: Binocular/vertical tube=100/0
Pull: Binocular/vertical tube=0/100

Attaching part for the
intermediate magnification
unit

(Refer to 3.21.)
Attach this unit to change
observation magnifications.

Connectors

(Refer to Figure 1.1-4.)

AC inlet

Connects the power cord exclusive
for the region of the product used
(optional).

Power switch

(Refer to 3.1.)
Set the switch to the “|” side to turn
on the power, or to the “

” side to

turn off the power.
When the power is turned on, the
POWER LED on the front-display
lights up.

Filter turret

(Refer to 3.10.)
Switch the turret when the ND
filter or other filters is/are turned.

Fine focus knob

(Refer to 3.7.)
Focus on the sample by
slightly lifting/lowering the
revolving nosepiece with
the fine knob.

Coarse focus knob

(Refer to 3.7.)
Focus on the sample roughly
lifting/lowering the revolving
nosepiece with the coarse
knob.

Optical path changeover
lever (eyepiece tube/back
port)

(Refer to 3.4.)
Press: Eyepiece tube/back
port =100/0
Pull: Eyepiece tube/back port
=55/45

Eyepiece tube clamp screw

Brightness control
dial

(Refer to 3.2.)
Adjusts the brightness
of the lamp.

Coarse torque
adjustment ring

(Refer to 3.7.)
Adjusts the rotation
residence.

Clamp
screws for
the filter
turret

Lamp air
vents

Содержание ECLIPSE MA200












































































































Результаты поиска

Содержание ECLIPSE MA200

Отзывы:

Похожие инструкции для ECLIPSE MA200

Бренды по названию

Популярные бренды

Nikon ECLIPSE MA200, Инструкция по эксплуатации

Результаты поиска

Содержание ECLIPSE MA200

Отзывы:

Похожие инструкции для ECLIPSE MA200

Бренды по названию

Популярные бренды