Nikon ECLIPSE MA200 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 107

background image

Chapter 3 Operation Details

57

3.23

Using the supporting pillar for dia-Illuminator 100W (MA2-DP)

Attach the supporting pillar for dia-Illuminator 100W to the MA200 main body to perform the microscopy under
the diascopic illumination.
To perform the microscopy, mount the D-LH/LC Lamphouse and condenser etc. to the supporting pillar for
dia-Illuminator 100W, and connect the power supply (TI-PS 100W) to the lamphouse.

Figure 3.23-1 Supporting pillar for dia-Illuminator 100W

3.23.1

Procedure for turning on the power switch

Figure 3.23-2 Procedure for turning on

the power switch

1 Be sure that the lamphouse on the supporting

pillar for dia-Illuminator is properly connected to
the power supply, and the brightness control dial
on MA200 main body is set to OFF.

2 Set the POWER switch to the “|” side on the power

supply.

The POWER indicator on the power supply and
the lamp light up.

3 Set the POWER switch to the “|” side to turn on

the MA200 main body.

The power LED on the front lights up.

4 To turn off the pillar illuminator, set the power

switch to the “

c

” side in the sequence of the fiber

illuminator, the MA200 main body.

* To adjust the brightness of the diascopic

illumination or to use the TI-PS 100W power
supply in detail, refer to the instruction manual
supplied with the equipment.

Lamphouse

Filter slider
Supporting pillar for
dia-Illuminator 100W

Condenser mount

Condenser

Power supply

1

Power switch ON

2

Power switch ON

POWER indicator

Light intensity
control dial

«
...
57
58
59
60
61
...
»

Содержание ECLIPSE MA200












































































































Отзывы:

Нет отзывов

Похожие инструкции для ECLIPSE MA200

Бренд: Leica Страницы: 48

Slit lamp BD 900

Бренд: Haag-Streit Страницы: 44

Eclipse LV100DA-U

Бренд: Nikon Страницы: 115

Бренд: Supereyes Страницы: 14

Бренд: Supereyes Страницы: 7

Бренд: Conrad Страницы: 4

Бренд: Conrad Страницы: 4

Бренд: Olympus Страницы: 24

Бренд: Olympus Страницы: 14

Бренд: Frigidaire Страницы: 5

Бренд: Frigidaire Страницы: 2

VS110 Fluorescence

Бренд: Olympus Страницы: 4

Бренд: Meta Media Страницы: 30

Бренд: TTS Страницы: 104

Бренд: Carson Страницы: 2

Бренд: Carson Страницы: 3

Бренд: Carson Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды