Nikon ECLIPSE MA200 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 107

background image

Chapter 3 Operation Details

40

3.10

Filter

Figure 3.10-1 Filter turret

Two quartet filter turrets are provided on the
microscope, and each filter turret has the

φ

25 mm

filters as shown below.
Each time you turn the turret 90 degrees, the next
filter enters the optical path. The display indicated on
the turret is the filter placed in the optical path. Select
the filter suitable for your purpose, and place it into
the optical path by turning the turret.
Each turret is provided with an optional (USER) slot
to add a desired filter. Use the slot if necessary. (For
attaching an optional filter, refer to “4.11.”)

Turret position

Filter

Indication

Usage

ND16
(Neutral Density filter)

ND16

Adjusts the brightness for general microscopy
or photomicroscopy. Reduces the light intensity
to 1/16. (Transmittance: approx. 6.3%)

ND4
(Neutral Density filter)

ND4

Adjusts the brightness for general microscopy
or photomicroscopy. Reduces the light intensity
to 1/4. (Transmittance: approx. 25%)

Optional

USER

Attach as desired

Turret 1:
on user-side

Dummy OPEN

Without

filters

GIF (Green Interference
filter)

GIF

Improves the contrast for microscopy under a
monochrome light or when performing
monochrome imaging.

NCB11 (Neutral Color
Balancing filter)

NCB

Corrects the color temperature for general
microscopy or filming by daylight color TV
camera photography. Color reproduction is best
when this filter is inserted into the optical path,
and the lamp voltage is set to the same display
as the lamp rating. Remove from optical path
when performing monochrome imaging.

Optional

USER

Attach as desired

Turret 2:
on far-side

Dummy OPEN

Without

filters

Filter currently
in the optical
path displayed

Filter turret 1

Filter turret 2

«
...
40
41
42
43
44
...
»

Содержание ECLIPSE MA200












































































































Отзывы:

Нет отзывов

Похожие инструкции для ECLIPSE MA200

Бренд: KERN Страницы: 21

Бренд: Bresser Junior Страницы: 60

Бренд: MshOt Страницы: 15

Бренд: Unitron Страницы: 18

Бренд: Unitron Страницы: 22

Бренд: ADB Страницы: 24

Primomic 114005

Бренд: Gundlach Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды