manualshive.com logo in svg

Nidec Digitax HD M753 EtherCAT, Руководство пользователя, Страница: 69 / 262

Поделиться
Скачать
Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 69

Safety 

information

Product 

information

Mechanical 

installation

Electrical 

installation

Getting 

started

Basic 

parameters

Running 

the motor

Optimization

EtherCAT 

interface

SD Card 

Operation

Onboard 

PLC

Advanced 

parameters

Diagnostics

UL listing 

information

Digitax HD M753 Control User Guide

69

Issue Number: 3

7.5

Setting up a feedback device

7.5.1

P1 position interface

This section shows the parameter settings which must be made to use each of the compatible feedback device types with P1 position interface on the 
drive. For more information on the parameters listed here please refer to the 

Parameter Reference Guide.

Table 7-3 Parameters required for feedback device set-up on the P1 position interface

Information required to be entered by the user.

●

Parameter can be set-up automatically by the drive through auto-configuration parameter. Must be set by the user if auto-configuration is disabled 
(i.e. Pr

03.041

 = Disabled (0)).

*

Pr

03.036

: If the output voltage from the encoder is > 5 V, then termination resistors must be disabled by setting Pr

03.039 

to 0. 

Table 7-3 shows a summary of the parameters required to set-up each feedback device. More detailed information follows.

Parameter

AB, FD, FR, AB Servo, 

SC, SC Servo, SC SC

FD Servo, FR Servo

SC 

Hiperface

SC 

EnDat

SC 

BiSS

SC 

SSI

SSI

EnDat BiSS

Resolver

P1 Marker Mode

 (03.031)

P1 Rotary Turns Bits

 (03.033)

●

●

●

●

●

P1 Rotary Lines Per Revolution

 (03.034)

●

●

●

P1 Comms Bits

 (03.035)

●

●

●

●

●

P1 Supply Voltage

 (03.036)*

P1 Comms Baud Rate

 (03.037)

P1 Device Type 

(03.038)

P1 Auto–configuration Select 

(03.041)

P1 SSI Binary Mode 

(03.048)

P1 Calculation time 

(03.060)

P1 Resolver Poles

 (03.065)

P1 Resolver Excitation

 (03.066)

P1 Additional Configuration

 (03.074)

●

●

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Отзывы:

Нет отзывов