Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 19

Страница: 19 / 262

Digitax HD M753 Control User Guide

Issue Number: 3

3.3

KI-Remote Keypad Adaptor installation

The M75X Remote Keypad Adaptor provides an EIA-485 port for permanent connection to a KI-Remote Keypad or the temporary attachment for PC
tool connection. The KI-Remote Keypad Adaptor is available from the supplier of the drive. Refer to Table 2-4

Additional options

on page 15.

Figure 3-4 Installing the KI-Remote Keypad Adaptor without display fitted

Align the KI-Remote Keypad Adaptor to the display housing and push on until it clicks into place.

Figure 3-5 Installing the KI-Remote Keypad Adaptor with display fitted

Unclip and pull the display away from the front cover. The tether keeps the display associated to the drive and should not be removed. A small

terminal screwdriver maybe required to unclip the display. A slot in the drive plastic is provided for this purpose (

Align the Remote Keypad Adaptor with the display housing noting the position of the notch (See view

above). Install the Remote Keypad

Adaptor over the display tether.

. Push the Remote Keypad Adaptor into the housing until it clicks into place.

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы:

Nidec Digitax HD M753 EtherCAT, Руководство пользователя, Страница: 19 / 262

Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы: