Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 262

Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 13

information

Digitax HD M753 Control User Guide

13

Issue Number: 3

2.4

Compatible position feedback devices

Table 2-1 Supported feedback devices

* This feedback device provides very low resolution feedback and should not be used for applications requiring a high level of performancee.

2.5

Nameplate description

The following labels are attached to the drive.

Figure 2-2 Typical drive rating labels

Date code format

The date code is four numbers. The first two numbers indicate the year and the remaining numbers indicate the week of the year in which the drive
was built.
Example: A date code of 1710 would correspond to week 10 of year 2017.

Encoder type

Pr 3.038 setting

Quadrature incremental encoders with or without marker pulse

AB (0)

Quadrature incremental encoders with UVW commutation signals for absolute position for permanent magnet
motors with or without marker pulse

AB Servo (3)

Forward / reverse incremental encoders with or without marker pulse

FR (2)

Forward / reverse incremental encoders with UVW commutation signals for absolute position for permanent
magnet motors with or without marker pulse

FR Servo (5)

Frequency and direction incremental encoders with or without marker pulse

FD (1)

Frequency and direction incremental encoders with UVW commutation signals for absolute position for permanent
magnet motors with or without marker pulse

FD Servo (4)

Sincos incremental encoders

SC (6)

Sincos incremental with commutation signals

SC Servo (12)

Heidenhain sincos encoders with EnDat comms for absolute position

SC EnDat (9)

Stegmann sincos encoders with Hiperface comms for absolute position

SC Hiperface (7)

Sincos encoders with SSI comms for absolute position

SC SSI (11)

Sincos incremental with absolute position from single sin and cosine signals

SC SC (15)

SSI encoders (Gray code or binary)

SSI (10)

EnDat communication only encoders

EnDat (8)

Resolver

Resolver (14)

UVW commutation only encoders*

Commutation only (16)

BiSS communication only encoders

BiSS (13)

Sincos encoders with BiSS communications

SC BiSS (17)

Approval

Voltage

Frequency Phases

Maximum phase
input current

Maximum continuous
output current

Voltage

Serial

number

Date code

Model

23.2A

Model

Frame

size

Drive

format

Input

Output

Voltage

Current

rating

Maximum phase
input current

Output current

Key to approvals

CE approval

Europe

RCM regulatory
compliance mark

Australia

UL / cUL approval

USA & Canada

RoHS compliant

China

Functional safety

USA & Canada

Eurasian conformity

Eurasia

R

NOTE

«
...
11
12
13
14
15
...
»

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Отзывы:

Нет отзывов