Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 226 | Manualshive

Страница: 226 / 262

Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 226

Diagnostics

226

Digitax HD M753 Control User Guide

Issue Number: 3

Autotune 3

Measured inertia has exceeded the parameter range or commutation signals changed in wrong direction

13

The drive has tripped during a rotating autotune or mechanical load measurement test. The cause of the trip can be
identified from the associated sub-trip number.

Recommended actions for sub-trip 2:

•

Check motor cable wiring is correct

•

Check feedback device U,V and W commutation signal wiring is correct

Recommended actions for sub-trip 3:

•

Increase the test level

•

If the test was carried out at standstill repeat the test with the motor rotating within the recommended speed range

Autotune 4

Drive encoder U commutation signal fail

14

A position feedback device with commutation signals is being used (i.e. AB Servo, FD Servo, FR Servo, SC Servo, or
Commutations only encoder) and the U commutation signal did not change during a rotating autotune.

Recommended actions:

•

Check feedback device U commutation signal wiring is correct (Encoder terminals 7 and 8)

Autotune 5

Drive encoder V commutation signal fail

15

A position feedback device with commutation signals is being used (i.e. AB Servo, FD Servo, FR Servo, SC Servo, or
Commutations only encoder) and the V commutation signal did not change during a rotating autotune.

Recommended actions:

•

Check feedback device V commutation signal wiring is correct (Encoder terminals 9 and 10)

Autotune 6

Drive encoder W commutation signal fail

16

A position feedback device with commutation signals is being used (i.e. AB Servo, FD Servo, FR Servo, SC Servo, or
Commutations only encoder) and the W commutation signal did not change during a rotating autotune.

Recommended actions:

•

Check feedback device W commutation signal wiring is correct (Encoder terminals 11 and 12)

Autotune 7

Motor number of poles / position feedback resolution set incorrectly

17

An

Autotune 7

trip is initiated during a rotating autotune, if the motor poles or the position feedback resolution have been

set up incorrectly where position feedback is being used.

Recommended actions:

•

Check line per revolution for feedback device

•

Check the number of poles in Pr

05.011

Autotune Stopped

Autotune test stopped before completion

18

The drive was prevented from completing an autotune test, because either the drive enable or the drive run were removed.

Recommended actions:

•

Check the drive enable signal (terminal 2 &6) were active during the autotune

•

Check the run command was active in Pr

08.005

during autotune

Brake R Too Hot

Braking resistor overload timed out (I

2

t)

19

The

Brake R Too Hot

indicates that braking resistor overload has timed out. The value in

Braking Resistor Thermal

Accumulator

(10.039) is calculated using

Braking Resistor Rated Power

(10.030),

Braking Resistor Thermal Time Constant

(10.031) and

Braking Resistor Resistance

(10.061). The

Brake R Too Hot

trip is initiated when

Braking Resistor Thermal

Accumulator

(10.039) reaches 100 %.

Recommended actions:

•

Ensure the values entered in Pr

10.030

, Pr

10.031

and Pr

10.061

are correct

•

If an external thermal protection device is being used and the braking resistor software overload protection is not
required, set Pr

10.030

, Pr

10.031

or Pr

10.061

to 0 to disable the trip.

Trip

Diagnosis

Sub-trip

Reason

1

Measured inertia has exceeded the parameter range during a mechanical load measurement

2

The commutation signals changed in the wrong direction during a rotating autotune

3

The mechanical load test has been unable to identify the motor inertia.

«
...
224
225
226
227
228
...
»

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Отзывы:

Нет отзывов