Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 249

Страница: 249 / 262

Digitax HD M753 Control User Guide

249

Issue Number: 3

User Prog Trip

Trip generated by an onboard user program

This trip can be initiated from within an onboard user program using a function call which defines the sub-trip number

Recommended actions:

•

Check the user program

User Save

User Save error / not completed

The

User Save

trip indicates that an error has been detected in the user save parameters saved in non-volatile memory.

For example, following a user save command, If the power to the drive was removed when the user parameters were being
saved.

Recommended actions:

•

Perform a user save in Pr

mm.000

to ensure that the trip doesn’t occur the next time the drive is powered up.

•

Ensure that the drive has enough time to complete the save before removing the power to the drive.

User Trip

User generated trip

40 -89

112 -159

These trips are not generated by the drive and are to be used by the user to trip the drive through an application program.

Recommended actions:

•

Check the user program

Watchdog

Control word watchdog has timed out

The

Watchdog

trip indicates that the control word has been enabled and has timed out.

Recommended actions:

Once Pr

06.042

bit 14 has been changed from 0 to 1 to enable the watchdog, this must be repeated every 1 s or a

Watchdog trip will be initiated. The watchdog is disabled when the trip occurs and must be re-enabled if required when the
trip is reset.

Trip

Diagnosis

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы:

Nidec Digitax HD M753 EtherCAT, Руководство пользователя, Страница: 249 / 262

Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы: