Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 241

Страница: 241 / 262

Digitax HD M753 Control User Guide

241

Issue Number: 3

OI Brake

Braking IGBT over current detected: short circuit protection for the braking IGBT activated

The

OI Brake

trip indicates that over current has been detected in braking IGBT or braking IGBT protection has been

activated.This trip cannot be reset until 10 s after the trip was initiated.

Recommended actions:

•

Check brake resistor wiring

•

Check braking resistor value is greater than or equal to the minimum resistance value

•

Check braking resistor insulation

OI dc

Power module over current detected from IGBT on state voltage monitoring

109

The

OI dc

trip indicates that the short circuit protection for the drive output stage has been activated. The table below

shows where the trip has been detected. This trip cannot be reset until 10 s after the trip was initiated.

Recommended actions:

•

Disconnect the motor cable at the drive end and check the motor and cable insulation with an insulation tester

•

Replace the drive

OI Snubber

Snubber over-current detected

The

OI Snubber

trip indicates that an over-current condition has been detected in the rectifier snubber circuit. The reason

for the trip can be identified by the sub-trip number.

* For a parallel power-module system the rectifier number will be one as it is not possible to determine which rectifier has
detected the fault.

Recommended actions:

•

Ensure the internal EMC Filter is installed

•

Ensure the motor cable length does not exceed the maximum for selected switching frequency

•

Check for supply voltage imbalance

•

Check for supply disturbance such as notching from a DC drive

•

Check the motor and motor cable insulation with an insulation tester

•

Install an output line reactor or sinusoidal filter

Option Disable

Option module does not acknowledge during drive mode changeover

215

The

Option Disable

trip indicates that the option module did not acknowledge to the drive that communications with the

drive has been stopped during the drive mode changeover with in the allocated time.

Recommended trip:

•

Reset the trip

•

If the trip persists, replace the option module

Out Phase Loss

Output phase loss detected

The

Out Phase Loss

trip indicates that phase loss has been detected at the drive output.

If Pr

05.042

= 1 the physical output phases are reversed, and so sub-trip 3 refers to physical output phase V and sub-trip 2

refers to physical output phase W.

Recommended actions:

•

Check motor and drive connections

•

To disable the trip set

Output Phase Loss Detection Enable

(06.059) = 0

Trip

Diagnosis

Source

Description

Power system

Power module number

Braking IGBT instantaneous over-current trip

Source

Control system

Power system

Power module number

Source

Description

Power system

Rectifier number*

Rectifier snubber over-current trip detected.

Sub-trip

Reason

U phase detected as disconnected when drive enabled to run.

V phase detected as disconnected when drive enabled to run.

W phase detected as disconnected when drive enabled to run.

Output phase loss detected when the drive is running.

NOTE

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы:

Nidec Digitax HD M753 EtherCAT, Руководство пользователя, Страница: 241 / 262

Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы: