Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 142

Страница: 142 / 262

142

Digitax HD M753 Control User Guide

Issue Number: 3

VM_DC_VOLTAGE_SET

Range applied to DC voltage reference parameters

Units

Range of [MIN]

Range of [MAX]

0 to 1150

Definition

VM_DC_VOLTAGE_SET[MAX] is drive voltage rating dependent. See Table 12-4.

VM_DC_VOLTAGE_SET[MIN] = 0

VM_DRIVE_CURRENT

Range applied to parameters showing current in A

Units

Range of [MIN]

-99999.999 to 0.000

Range of [MAX]

0.000 to 99999.999

Definition

VM_DRIVE_CURRENT[MAX] is equivalent to the full scale (over current trip level) for the drive and is given by

Full

Scale Current Kc

(11.061).

VM_DRIVE_CURRENT[MIN] = - VM_DRIVE_CURRENT[MAX]

VM_DRIVE_CURRENT_UNIPOLAR

Unipolar version of VM_DRIVE_CURRENT

Units

Range of [MIN]

0.000

Range of [MAX]

0.000 to 99999.999

Definition

VM_DRIVE_CURRENT_UNIPOLAR[MAX] = VM_DRIVE_CURRENT[MAX]

VM_DRIVE_CURRENT_UNIPOLAR[MIN] = 0.000

VM_HIGH_DC_VOLTAGE

Range applied to parameters showing high DC voltage

Units

Range of [MIN]

Range of [MAX]

0 to 1500

Definition

VM_HIGH_DC_VOLTAGE[MAX] is the full scale d.c. link voltage feedback for the high d.c. link voltage measurement
which can measure the voltage if it goes above the normal full scale value. See Table 12-4.

VM_HIGH_DC_VOLTAGE[MIN] = 0

VM_LOW_UNDER_VOLTS

Range applied to the low under-voltage threshold

Units

Range of [MIN]

Range of [MAX]

24 to 1150

Definition

Back-up Mode Enable

(06.068) = 0:

VM_LOW_UNDER_VOLTS[MAX] = VM_STD_UNDER_VOLTS[MIN]
If

Back-up Mode Enable

(06.068) = 1:

VM_LOW_UNDER_VOLTS[MAX] = VM_STD_UNDER_VOLTS[MIN] / 1.1.

VM_LOW_UNDER_VOLTS[MIN] = 24.

VM_MIN_SWITCHING_FREQUENCY

Range applied to the minimum switching frequency parameter

Units

User units

Range of [MIN]

Range of [MAX]

0 to 6

Definition

VM_MIN_SWITCHING_FREQUENCY[MAX] =

Maximum Switching Frequency

(05.018)

VM_MIN_SWITCHING_FREQUENCY[MIN] = 0 for motor control modes, or 1 for Regen mode (subject to the
maximum)

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы:

Nidec Digitax HD M753 EtherCAT, Руководство пользователя, Страница: 142 / 262

Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы: