Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 262

Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 130

130

Digitax HD M753 Control User Guide

Issue Number: 3

10 SD Card Operation

10.1

Introduction

The Non-Volatile Media Card feature enables simple configuration of
parameters, parameter back-up, storing / reading PLC programs and
drive copying using an SD card storing / reading PLC programs.
The SD Card can be used for:
•

Parameter copying between drives

•

Saving drive parameter sets

•

Saving an onboard user program

The SC Card slot is located at the middle of the module, adjacent to the
drive compact display (if installed) on the right-hand side.
Ensure the SD Card is inserted with the contacts facing the left-hand
side of the drive.
The drive only communicates with the SD Card when commanded to
read or write, meaning the card may be "hot swapped".

Figure 10-1 Installation of the SD Card

1. Installing the SD Card
2. SD Card installed

10.2

SD Card support

The SD Card can be used to store drive parameter sets and / or PLC
programs set from the Digitax HD in data blocks 001 to 499 on the card.

If the read only flag is set then only codes 6yyy or 9777 are effective.

Figure 10-2 Basic SD Card operation

The whole card may be protected from writing or erasing by setting the
read-only flag as detailed section 10.3.9

9888 / 9777 - Setting and

clearing the SD Card read only flag

The card should not be removed during data transfer, as the drive will
produce a trip. If this occurs then either the transfer should be
reattempted or in the case of a card to drive transfer, default parameters
should be loaded.

Beware of possible live terminals when installing the
SD Card.

WARNING

1

2

NOTE

NOTE

Boot

Drive reads all
parameters from
the SD Card

Pr

00.030

= Read +

Programs all drive
parameters to the
SD Card

Overwrites any
data already in
data block 1

Pr

00.030

= P

Drive automatically
writes to the SD Card
when a parameter
save is performed

Auto

Save

Pr

00.030

= Auto +

Auto

Save

Drive boots from the
SD Card on power
upand automatically
writes to the SD Card
when a parameter
save is performed

Pr

00.030

= Boot +

«
...
128
129
130
131
132
...
»

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Отзывы:

Нет отзывов