Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 150

Страница: 150 / 262

150

Digitax HD M753 Control User Guide

Issue Number: 3

Parameter

Range(



)

Default(



)

Type

RFC-A / S

RFC-A

RFC-S

01.001

Reference Selected

VM_SPEED_FREQ_REF Hz

VM_SPEED_FREQ_REF rpm

RO Num ND NC PT

01.002

Pre-Skip Filter Reference

VM_SPEED_FREQ_REF Hz

VM_SPEED_FREQ_REF rpm

RO Num ND NC PT

01.003

Pre-Ramp Reference

VM_SPEED_FREQ_REF Hz

VM_SPEED_FREQ_REF rpm

RO Num ND NC PT

01.004

Reference Offset

VM_SPEED_FREQ_REF Hz

VM_SPEED_FREQ_REF rpm

0.0

RW Num

01.005

Jog Reference

0.0 to 400.0 Hz

0.0 to 4000.0 rpm

0.0

RW Num

01.006

Maximum Reference Clamp

VM_POSITIVE_REF_

CLAMP1 Hz

VM_POSITIVE_REF_

CLAMP1 rpm

50 Hz: 50.0
60 Hz: 60.0

50Hz: 1500.0
60Hz: 1800.0

3000.0 RW Num

01.007

Minimum Reference Clamp

VM_NEGATIVE_REF_

CLAMP1 Hz

VM_NEGATIVE_REF_

CLAMP1 rpm

0.0

RW Num

01.008

Negative Reference Clamp Enable

Off (0) or On (1)

Off (0)

Bit

01.009

Reference Offset Select

Off (0) or On (1)

Off (0)

Bit

01.010

Bipolar Reference Enable

Off (0) or On (1)

Off (0)

Bit

01.011

Reference On

Off (0) or On (1)

Bit

ND NC PT

01.012

Reverse Select

Off (0) or On (1)

Bit

ND NC PT

01.013

Jog Select

Off (0) or On (1)

Bit

ND NC PT

01.014

Reference Selector

A1 A2 (0), A1 Preset (1), A2 Preset (2), Preset (3), Keypad (4),

Precision (5), Keypad Ref (6)

A1 Preset (1)

Txt

01.015

Preset Selector

0 to 9

RW Num

01.016

Preset Selector Time

0.0 to 400.0 s

10.0 s

RW Num

01.017

Keypad Control Mode Reference

VM_SPEED_FREQ_KEYPAD_REF

0.0

RO Num

NC PT PS

01.018

Precision Reference Coarse

VM_SPEED_FREQ_REF

0.0

RW Num

01.019

Precision Reference Fine

0.000 to 0.099 Hz

0.000 to 0.099 rpm

0.000

RW Num

01.020

Precision Reference Update Disable

Off (0) or On (1)

Off (0)

Bit

01.021

Preset Reference 1

VM_SPEED_FREQ_REF

0.0

RW Num

01.022

Preset Reference 2

VM_SPEED_FREQ_REF

0.0

RW Num

01.023

Preset Reference 3

VM_SPEED_FREQ_REF

0.0

RW Num

01.024

Preset Reference 4

VM_SPEED_FREQ_REF

0.0

RW Num

01.025

Preset Reference 5

VM_SPEED_FREQ_REF

0.0

RW Num

01.026

Preset Reference 6

VM_SPEED_FREQ_REF

0.0

RW Num

01.027

Preset Reference 7

VM_SPEED_FREQ_REF

0.0

RW Num

01.028

Preset Reference 8

VM_SPEED_FREQ_REF

0.0

RW Num

01.029

Skip Reference 1

0.0 to 550.0 Hz

0 to 33, 000 rpm

0.0

RW Num

01.030

Skip Reference Band 1

0.0 to 25.0 Hz

0 to 250 rpm

0.0

RW Num

01.031

Skip Reference 2

0.0 to 550.0 Hz

0 to 33, 000 rpm

0.0

RW Num

01.032

Skip Reference Band 2

0.0 to 25.0 Hz

0 to 250 rpm

0.0

RW Num

01.033

Skip Reference 3

0.0 to 550.0 Hz

0 to 33, 000 rpm

0.0

RW Num

01.034

Skip Reference Band 3

0.0 to 25.0 Hz

0 to 250 rpm

0.0

RW Num

01.035

Reference In Rejection Zone

Off (0) or On (1)

Bit

ND NC PT

01.036

Analog Reference 1

VM_SPEED_FREQ_USER_

REFS Hz

VM_SPEED_FREQ_USER_

REFS rpm

0.0

RO Num

01.037

Analog Reference 2

0.0

RO Num

01.038

Percentage Trim

±100.00 %

0.00 %

RW Num

01.039

Speed Feed-forwards

VM_SPEED_FREQ_REF

RO Num ND NC PT

01.040

Speed Feed-forwards Select

Off (0) or On (1)

Bit

ND NC PT

01.041

Reference Select Flag 1

Off (0) or On (1)

Off (0)

Bit

01.042

Reference Select Flag 2

Off (0) or On (1)

Off (0)

Bit

01.043

Reference Select Flag 3

Off (0) or On (1)

Off (0)

Bit

01.044

Reference Select Flag 4

Off (0) or On (1)

Off (0)

Bit

01.045

Preset Select Flag 1

Off (0) or On (1)

Off (0)

Bit

01.046

Preset Select Flag 2

Off (0) or On (1)

Off (0)

Bit

01.047

Preset Select Flag 3

Off (0) or On (1)

Off (0)

Bit

01.048

Preset Selector Timer Reset

Off (0) or On (1)

Off (0)

Bit

01.049

Reference Selected Indicator

1 to 6

RO Num ND NC PT

01.050

Preset Selected Indicator

1 to 8

RO Num ND NC PT

01.051

Power-up Keypad Control Mode
Reference

Reset (0), Last (1), Preset (2)

Reset (0)

Txt

01.055

Linear Speed Select

Off (0) or On (1)

Off (0)

Bit

01.056

Linear Speed Selected

Off (0) or On (1)

Bit

ND NC PT

01.057

Force Reference Direction

None (0), Forward (1), Reverse (2)

None (0)

Txt

RW Read / Write

Read only

Num Number parameter

Bit

Bit parameter

Txt

Text string

Bin

Binary parameter

Filtered

ND No default value

Not copied

Protected parameter

Rating dependent

User save

Power-down save

Destination

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы:

Nidec Digitax HD M753 EtherCAT, Руководство пользователя, Страница: 150 / 262

Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы: