Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 165

Страница: 165 / 262

Digitax HD M753 Control User Guide

165

Issue Number: 3

03.172

P2 Status

None (0), AB (1), FD (2), FR (3), EnDat (4), SSI (5),

EnDat Alt (7), SSI Alt (8)

Txt

ND NC PT

03.173

P2 Absolute Turns Recovery Enable

Off (0) or On (1)

Off (0)

Bit

03.174

P1 Additional Configuration

0 to 511116116

RW Read / Write

Read only

Num Number parameter

Bit

Bit parameter

Txt

Text string

Bin

Binary parameter

Filtered

ND No default value

Not copied

Protected parameter

Rating dependent

User save

Power-down save

Destination

Parameter

Range

Default

Type

RFC-A

RFC-S

RFC-A

RFC-S

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы:

Nidec Digitax HD M753 EtherCAT, Руководство пользователя, Страница: 165 / 262

Результаты поиска

Содержание Digitax HD M753 EtherCAT

Отзывы: