Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 162

background image

16

1 PART NAMES

*1 If both the CQ LED and Q LED flash, a short-circuit has occurred between the L+ and L- terminals.

The US LED, UA LED, LINK LED (P1), L ER LED (P1). LINK LED (P2), and L ER LED (P2) may turn on when
the module is powered on. This behavior does not indicate an error.

(4)

LINK LED(P1)

Indicates the link status of the PORT1 connector.
On: Linkup in progress
Off: Linkdown in progress

L ER LED(P1)

Indicates the port status of the PORT1 connector.
Green: The IO-Link module received normal data.
Green (flashing): The network is configured in ring topology without using the loopback function.
Red: The IO-Link module received abnormal data.
Off: Linkdown in progress

(5)

LINK LED(P2)

Indicates the link status of the PORT2 connector.
On: Linkup in progress
Off: Linkdown in progress

L ER LED(P2)

Indicates the port status of the PORT2 connector.
Green: The IO-Link module received normal data.
Green (flashing): The network is configured in ring topology without using the loopback function.
Red: The IO-Link module received abnormal data.
Off: Linkdown in progress

(6)

CQ LED

Indicates the operating status of the CQ terminal of each channel.

■

In IO-Link mode

Green: Operating normally with IO-Link enabled.
Green (flashing every 0.5s): Communication is stopped with IO-Link enabled.
Green (flashing every 0.3s): Uploading IO-Link device parameters to the data storage, or downloading IO-Link device
parameters from the data storage
Red (flashing): An error is occurring due to any of the following reasons.

• The IO-Link device validation setting is enabled, and an IO-Link device is not compatible or identifiable.
• The data storage configuration is enabled, and an incompatible IO-Link device is connected.
• The configured process data size is smaller than that of the connected IO-Link devices.
• The module/sensor power supply (US) voltage is 13V or less.

Off: IO-Link is disabled.

■

In SIO mode

Orange: I/O is on.
Off: I/O is off.
Red: An I/O setting error has occurred (short-circuit detection).
Red (flashing): An error has occurred (short-circuit detection).

(7)

Q LED

Indicates the operating status of the Q terminal of each channel.
Orange: I/O is on.
Off: I/O is off.
Red: An I/O setting error has occurred (short-circuit detection).
Red (flashing): An error has occurred (short-circuit detection).

No.

Name

Description

«
...
16
17
18
19
20
...
»

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Jabra Страницы: 4

Бренд: Watts Страницы: 4

Бренд: WaterCop Страницы: 4

Бренд: Watlow Страницы: 59

Tekmar WiFi Snow Melting Control 670

Бренд: Watts Страницы: 48

Бренд: Vacon Страницы: 132

Frigolink FVB110B

Бренд: WURM Страницы: 4

Бренд: Fibocom Страницы: 79

Бренд: oventrop Страницы: 40

Бренд: Sentiotec Страницы: 45

ZoneSense Plus AS

Бренд: Halma Страницы: 58

Бренд: Netro Страницы: 14

Бренд: Mosa Страницы: 28

Бренд: Conductrix Wampfler Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды