Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 162

background image

11 TROUBLESHOOTING

11.5 Checking for the Error Codes and the Warning Codes

125

11

Checking on the display part

A maximum of 16 error codes of major errors that have occurred can be checked on the display part. (Moderate and minor
errors are not displayed.)
The 17th and subsequent major errors are not displayed.

Operating procedure

The IO-Link module does not operate properly if a major error occurs, therefore the error content may not be
checked with the engineering tool.
In this case, check the error content on the display part.
If the error content cannot be checked on the display part either, the IO-Link module may be in failure. Please
consult your local Mitsubishi representative.

1.

Press the [SEL.] button on the module information window of the main menu, and
select the major error window. Number of the occurred errors can be checked on the
major error window.

2.

Press and hold the [SET] button on the major error window to check the error code.
The error codes are displayed one by one by pressing the [SEL.] button. Pressing the
[SEL.] button on the "PAGE 15" window, the display returns to the "PAGE 0" window.
The windows are displayed as follows.

• 1st line: Page number ("PAGE 0" to "PAGE 15")
• 2nd line: Error code (



Page 126 List of Error Codes and the Warning Codes)

• 3rd line: Information to be used in the system

3.

Press [SET] button to go back to the major error window.

«
...
125
126
127
128
129
...
»

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

Бренд: Ubisys Страницы: 2

Бренд: KELCO Страницы: 36

Бренд: Hansen Страницы: 4

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: TCS Basys Controls Страницы: 2

Бренд: Aalborg Страницы: 15

Бренд: Aalborg Страницы: 48

Бренд: Accel Страницы: 8

Бренд: Daikin Страницы: 38

Бренд: Daikin Страницы: 2

Бренд: Daikin Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды