Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 162

background image

140

APPX
Appendix 2 Remote Registers

Details of Remote Registers

Module status area (RWr0)

■

Initial processing request flag (RWr0.b8)

The operations of Initial processing request flag (RWr0.b8) and Initial processing completion flag (RWw0.b8) vary depending
on the setting value of Initial operation setting.
For details on the initial operation setting, refer to the following.



Page 84 Initial operation setting

• When With initial processing is set
After the module is powered on, Initial processing request flag (RWr0.b8) turns on. Create a program where initial processing
is executed by using Initial processing request flag (RWr0.b8) and Initial processing completion flag (RWw0.b8). When Initial
processing completion flag (RWw0.b8) is turned on, Remote READY (RWr0.b11) turns on. Also when Initial processing
completion flag (RWw0.b8) is turned on, Initial processing request flag (RWr0.b8) turns off.

When setting parameters using Initial processing request flag (RWr0.b8) as an interlock as shown in the
program example, set "Initial operation setting" to "With initial processing". After that, perform initial
processing and check that Remote READY (RWr0.b11) is on.
For program examples of initial processing, refer to the following.

Page 105 Program example

*1 When data link starts at the same time of when the module is powered on
*2 When an external input device connected to X0 is on

(1) The setting value is changed by a program.
(2) The operation starts with the setting value A.

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

(2)

(1)

500ms

Initial processing request flag (RWr0.b8)

(Setting value A)

Default

Module power supply

*1

Channel 1 (CQ) external input signal 0

(RX0)

*2

Controlled by the IO-Link module

Controlled by the program

Initial processing completion flag (RWw0.b8)

Remote READY (RWr0.b11)

Module setting

«
...
140
141
142
143
144
...
»

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: QCON Страницы: 4

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

Бренд: Parker Страницы: 54

Бренд: RAM Страницы: 71

Бренд: Automated Logic Страницы: 10

Бренд: Atmel Страницы: 12

Бренд: Nibe Страницы: 92

Бренд: UMAX Technologies Страницы: 54

Бренд: KELCO Страницы: 4

iMO-LEARN - MDM

Бренд: i3-TECHNOLOGIES Страницы: 2

ROC 1407 - CODE

Бренд: THOMSON Страницы: 2

Бренд: Uniteck Страницы: 46

Бренд: Tele Radio Страницы: 17

Бренд: TAC Страницы: 4

Бренд: SGS electronic Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды